参数资料
| 型号： | XCR3256XL-7CS280C |
| 厂商： | Xilinx Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC CPLD 256MCELL 3.3V HP 280CSP |
| 标准包装： | 119 |
| 系列： | CoolRunner XPLA3 |
| 可编程类型： | 系统内可编程（最少 1K 次编程/擦除循环） |
| 最大延迟时间 tpd(1)： | 7.0ns |
| 电压电源 - 内部： | 3 V ~ 3.6 V |
| 逻辑元件/逻辑块数目： | 16 |
| 宏单元数： | 256 |
| 门数： | 6000 |
| 输入/输出数： | 164 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 280-TFBGA，CSPBGA |
| 供应商设备封装： | 280-CSBGA（16x16） |
| 包装： | 托盘 |
CoolRunner XPLA3 CPLD
DS012 (v2.5) May 26, 2009
Product Specification
R
mented in the buried macrocell can be fed back to the ZIA
via the macrocell feedback path.
If a macrocell pin is configured as a registered input, there is
a direct path to the register to provide a fast input setup
time. If the macrocell is configured as a latch, the register
clock input functions as the latch enable, with the latch
transparent when this signal is High. The hardwired clock
enable is non-functional when the macrocell is configured
as a latch.
I/O Cell
The OE (Output Enable) multiplexer has eight possible
modes (Figure 6). When the I/O Cell is configured as an
input (or 3-stated output), a half latch feature exists. This
half latch pulls the input High (through a weak pull-up) if the
input should float and cross the threshold. This protects the
input from staying in the linear region and causing an
increased amount of power consumption. This same weak
pull-up can be enabled in software such that it is always on
when the I/O Cell is configured as an input. This weak pull
up is automatically turned on when a pin is unused by the
design.
The I/O Cell is 5V tolerant when the device is powered.
Each output has independent slew rate control (fast or slow)
which assists in reducing EMI emissions.
See individual device data sheets for 3.3V PCI electrical
specification compatibility.
Note that an I/O macrocell used as buried logic that does
not have the I/O pin used for input is considered to be
unused, and the weak pull-up resistors will be turned on. It
is recommended that any unused I/O pins on the CoolRun-
ner XPLA3 family of CPLDs be left unconnected. Dedicated
input pins (CLKx/INx) do not have on-chip weak pull-up
resistors; therefore unused dedicated input pins must have
external termination. As with all CMOS devices, do not
allow inputs to float.
Figure 5: XPLA3 Macrocell Architecture
Global CLK
Universal CLK
P-term CLK
CT [4:7]
ds012_05_122299
Universal PST
CT [0:5]
Universal RST
CT [0:5]
To ZIA
To I/O
PAD
Note: Global CLK signals come from pins.
To ZIA
VFM
RST
PST
D/T/L
CLKEn
Q
CT4
P-term
48
PLA OR Term
From PT Array
1
Figure 6: I/O Cell
GND (Weak P.U.)
VCC
Universal OE
CT
GND
OE [2:0]
To Macrocell / ZIA
From Macrocell
I/O Pin
WP
Slew
Control
OE
Decode
0
1
2
3
4
5
6
7
I/O Pin
State
3-State
Function CT0
Function CT1
Function CT2
Function CT6
Universal OE
Enable
Weak P.U.
ds012_06_121699
Weak Pull-up
OE = 7
VCC
3
4
相关PDF资料 |
PDF描述 |
|---|---|
| XCS10-3VQG100C | IC FPGA 5V C-TEMP 100-VQFP |
| XCV600E-8HQ240C | IC FPGA 1.8V C-TEMP 240-HQFP |
| XCV812E-8FG900C | IC FPGA 1.8V C-TEMP 900-FBGA |
| XE8801AMI000WP | SENSING MACHINE WITH 16 + 10 BIT |
| XE8802MI035LF | IC DAS 16BIT FLASH 8K 100-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCR3256XL-7CS280I | 制造商:XILINX 制造商全称:XILINX 功能描述:256 Macrocell CPLD |
| XCR3256XL-7CSG280C | 制造商:Xilinx 功能描述:XLXXCR3256XL-7CSG280C IC SYSTEM GATE 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 6K GATES 256 MCRCLLS 166.67MHZ 0.35UM - Trays |
| XCR3256XL-7FT256C | 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 6K GATES 256 MCRCLLS 166.67MHZ 0.35UM - Trays |
| XCR3256XL-7FT256I | 制造商:XILINX 制造商全称:XILINX 功能描述:256 Macrocell CPLD |
| XCR3256XL-7FTG256C | 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 6K GATES 256 MCRCLLS 166.67MHZ COMM 0. - Trays |
发布紧急采购，3分钟左右您将得到回复。