- 您现在的位置：买卖IC网 > PDF目录19664 > XCR3384XL-10FG324C (Xilinx Inc)IC CPLD 3.3V ZERO PWR 324-FBGA PDF资料下载
参数资料
| 型号： | XCR3384XL-10FG324C |
| 厂商： | Xilinx Inc |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC CPLD 3.3V ZERO PWR 324-FBGA |
| 标准包装： | 60 |
| 系列： | CoolRunner XPLA3 |
| 可编程类型： | 系统内可编程（最少 1K 次编程/擦除循环） |
| 最大延迟时间 tpd(1)： | 9.0ns |
| 电压电源 - 内部： | 3 V ~ 3.6 V |
| 逻辑元件/逻辑块数目： | 24 |
| 宏单元数： | 384 |
| 门数： | 9000 |
| 输入/输出数： | 220 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 324-BBGA |
| 供应商设备封装： | 324-FBGA（23x23） |
| 包装： | 托盘 |
| 其它名称： | XCR3384XL10FG324C |
CoolRunner XPLA3 CPLD
8
DS012 (v2.5) May 26, 2009
Product Specification
R
3V, In-System Programming (ISP)
CoolRunner XPLA3 CPLDs allow for 3V, in-system pro-
gramming/reprogramming of its EEPROM cells via a JTAG
interface. An on-chip charge pump eliminates the need for
externally provided super-voltages. This allows program-
ming on the circuit board using only the 3V supply required
by the device for normal operation. The ISP commands
implemented in CoolRunner XPLA3 CPLDs are specified in
Table 4: XPLA3 Low-level JTAG Boundary-scan Commands
Instruction
(Instruction
Code)
Register Used
Description
Sample/Preload
(00010)
Boundary-scan
Register
The mandatory Sample/Preload instruction allows a snapshot of the normal operation of the
component to be taken and examined. It also allows data values to be loaded into the latched parallel
outputs of the Boundary-scan Shift Register prior to selection of the other boundary-scan test
instructions.
Extest
(00000)
Boundary-scan
Register
The mandatory Extest instruction allows testing of off-chip circuitry and board level interconnections.
Data is typically loaded onto the latched parallel outputs of Boundary-scan Shift Register using the
Sample/Preload instruction prior to selection of the Extest instruction.
Bypass
(11111)
Bypass Register
Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass
synchronously through the selected device to adjacent devices during normal device operation. The
Bypass instruction can be entered by holding TDI at a constant High value and completing an
Instruction-scan cycle.
Idcode
(00001)
Boundary-scan
Register
Selects the Idcode register and places it between TDI and TDO, allowing the Idcode to be serially
shifted out of TDO. The Idcode instruction permits blind interrogation of the components assembled
onto a printed circuit board. Thus, in circumstances where the component population can vary, it is
possible to determine what components exist in a product.
High-Z
(00101)
Bypass Register
The High-Z instruction places the component in a state which all of its system logic outputs are placed
in an inactive drive state (e.g., high impedance). In this state, an in-circuit test system can drive
signals onto the connections normally driven by a component output without incurring the risk of
damage to the component. The High-Z instruction also forces the Bypass Register between TDI and
TDO.
Intest
(00011)
Boundary-scan
Register
The Intest instruction selects the boundary scan register prior to applying tests to the logic core of the
device. This permits testing of on-chip system logic while the component is already on the board.
Table 5: JTAG Pin Description
Pin
Name
Description
TCK
Test Clock Input
Clock pin to shift the serial data and instructions in and out of the TDI and TDO pins,
respectively.
TMS
Test Mode Select
Serial input pin selects the JTAG instruction mode. TMS should be driven High during
user mode operation.
TDI
Test Data Input
Serial input pin for instructions and test data. Data is shifted in on the rising edge of
TCK.
TDO
Test Data Output
Serial output pin for instructions and test data. Data is shifted out on the falling edge
of TCK. The signal is 3-stated if data is not being shifted out of the device.
相关PDF资料 |
PDF描述 |
|---|---|
| EEC07DRYN-S13 | CONN EDGECARD 14POS .100 EXTEND |
| MCP9843-BE/ST | IC TEMP SENSOR DGTL 8-TSSOP |
| EEC07DRYH-S13 | CONN EDGECARD 14POS .100 EXTEND |
| XC2C512-7FGG324C | IC CR-II CPLD 512MCELL 324-FBGA |
| GBC06DRYN | CONN EDGECARD 12POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCR3384XL-10FG324I | 功能描述:IC CPLD 3.3V ZERO PWR 324-FBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - CPLD（复杂可编程逻辑器件） 系列:CoolRunner XPLA3 标准包装:40 系列:ispMACH® 4000C 可编程类型:系统内可编程 最大延迟时间 tpd(1):5.0ns 电压电源 - 内部:1.65 V ~ 1.95 V 逻辑元件/逻辑块数目:32 宏单元数:512 门数:- 输入/输出数:128 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:176-LQFP 供应商设备封装:176-TQFP（24x24） 包装:托盘 |
| XCR3384XL-10FGG324C | 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 9K GATES 384 MCRCLLS 125MHZ 0.35UM 3.3 - Trays |
| XCR3384XL-10FGG324I | 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 9K GATES 384 MCRCLLS 125MHZ 0.35UM 3.3 - Trays |
| XCR3384XL-10FT256C | 功能描述:IC CPLD 3.3V ZERO PWR 256-BGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - CPLD（复杂可编程逻辑器件） 系列:CoolRunner XPLA3 标准包装:40 系列:ispMACH® 4000C 可编程类型:系统内可编程 最大延迟时间 tpd(1):5.0ns 电压电源 - 内部:1.65 V ~ 1.95 V 逻辑元件/逻辑块数目:32 宏单元数:512 门数:- 输入/输出数:128 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:176-LQFP 供应商设备封装:176-TQFP（24x24） 包装:托盘 |
| XCR3384XL-10FT256I | 功能描述:IC CPLD 3.3V ZERO PWR 256-BGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - CPLD（复杂可编程逻辑器件） 系列:CoolRunner XPLA3 标准包装:40 系列:ispMACH® 4000C 可编程类型:系统内可编程 最大延迟时间 tpd(1):5.0ns 电压电源 - 内部:1.65 V ~ 1.95 V 逻辑元件/逻辑块数目:32 宏单元数:512 门数:- 输入/输出数:128 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:176-LQFP 供应商设备封装:176-TQFP（24x24） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。