- 您现在的位置：买卖IC网 > PDF目录300152 > XCS20XL-3BG280I (Xilinx, Inc.) Spartan and Spartan-XL Families Field Programmable Gate Arrays PDF资料下载
参数资料
| 型号： | XCS20XL-3BG280I |
| 厂商： | Xilinx, Inc. |
| 英文描述： | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| 中文描述： | 斯巴达和Spartan - xL的家庭现场可编程门阵列 |
| 文件页数： | 82/82页 |
| 文件大小： | 863K |
| 代理商： | XCS20XL-3BG280I |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页当前第82页
Spartan and Spartan-XL Families Field Programmable Gate Arrays
DS060 (v1.6) September 19, 2001
Product Specification
1-800-255-7778
R
Output Multiplexer/2-Input Function Generator
(Spartan-XL only)
The output path in the Spartan-XL IOB contains an addi-
tional multiplexer not available in the Spartan IOB. The mul-
tiplexer can also be configured as a 2-input function
generator, implementing a pass gate, AND gate, OR gate,
or XOR gate, with 0, 1, or 2 inverted inputs.
When configured as a multiplexer, this feature allows two
output signals to time-share the same output pad, effec-
tively doubling the number of device outputs without requir-
ing a larger, more expensive package. The select input is
the pin used for the output flip-flop clock, OK.
When the multiplexer is configured as a 2-input function
generator, logic can be implemented within the IOB itself.
Combined with a Global buffer, this arrangement allows
very high-speed gating of a single signal. For example, a
wide decoder can be implemented in CLBs, and its output
gated with a Read or Write Strobe driven by a global buffer.
The user can specify that the IOB function generator be
used by placing special library symbols beginning with the
letter "O." For example, a 2-input AND gate in the IOB func-
tion generator is called OAND2. Use the symbol input pin
labeled "F" for the signal on the critical path. This signal is
placed on the OK pin — the IOB input with the shortest
delay to the function generator. Two examples are shown in
Output Buffer
An active High 3-state signal can be used to place the out-
put buffer in a high-impedance state, implementing 3-state
outputs or bidirectional I/O. Under configuration control, the
output (O) and output 3-state (T) signals can be inverted.
The polarity of these signals is independently configured for
each IOB (see Figure 6, page 7). An output can be config-
ured as open-drain (open-collector) by tying the 3-state pin
(T) to the output signal, and the input pin (I) to Ground.
By default, a 5V Spartan device output buffer pull-up struc-
ture is configured as a TTL-like totem-pole. The High driver
is an n-channel pull-up transistor, pulling to a voltage one
transistor threshold below VCC. Alternatively, the outputs
can be globally configured as CMOS drivers, with additional
p-channel pull-up transistors pulling to VCC. This option,
applied using the bitstream generation software, applies to
all outputs on the device. It is not individually programma-
ble.
All Spartan-XL device outputs are configured as CMOS
drivers, therefore driving rail-to-rail. The Spartan-XL outputs
are individually programmable for 12 mA or 24 mA output
drive.
Any 5V Spartan device with its outputs configured in TTL
mode can drive the inputs of any typical 3.3V device. Sup-
ported destinations for Spartan/XL device outputs are
shown in Table 7.
Three-State Register (Spartan-XL Only)
Spartan-XL devices incorporate an optional register control-
ling the three-state enable in the IOBs. The use of the
three-state control register can significantly improve output
enable and disable time.
Output Slew Rate
The slew rate of each output buffer is, by default, reduced,
to minimize power bus transients when switching non-criti-
cal signals. For critical signals, attach a FAST attribute or
property to the output buffer or flip-flop.
Spartan/XL devices have a feature called "Soft Start-up,"
designed to reduce ground bounce when all outputs are
turned on simultaneously at the end of configuration.
When the configuration process is finished and the device
starts up, the first activation of the outputs is automatically
slew-rate limited. Immediately following the initial activation
of the I/O, the slew rate of the individual outputs is deter-
mined by the individual configuration option for each IOB.
Pull-up and Pull-down Network
Programmable pull-up and pull-down resistors are used for
tying unused pins to VCC or Ground to minimize power con-
sumption and reduce noise sensitivity. The configurable
pull-up resistor is a p-channel transistor that pulls to VCC.
The configurable pull-down resistor is an n-channel transis-
tor that pulls to Ground. The value of these resistors is typi-
cally 20 K
Figure 7: AND and MUX Symbols in Spartan-XL IOB
DS060_07_081100
OAND2
OMUX2
F
D0
D1
O
S0
相关PDF资料 |
PDF描述 |
|---|---|
| XCS20XL-3BG84I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS100C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS100I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS144C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS144I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCS20XL-3BG84C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3BG84I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS100C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS100I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20XL-3CS144C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
发布紧急采购，3分钟左右您将得到回复。