参数资料
型号: XPC8255CVVIFBC
厂商: Freescale Semiconductor
文件页数: 3/41页
文件大小: 0K
描述: IC MPU POWERQUICC II 480-TBGA
标准包装: 21
系列: MPC82xx
处理器类型: 32-位 MPC82xx PowerQUICC II
速度: 200MHz
电压: 2.5V
安装类型: 表面贴装
封装/外壳: 480-LBGA
供应商设备封装: 408-TBGA(37.5x37.5)
包装: 托盘
MPC8260 PowerQUICC II Integrated Communications Processor Hardware Specifications, Rev. 2
Freescale Semiconductor
11
Electrical and Thermal Characteristics
2.3.1
Layout Practices
Each VCC pin should be provided with a low-impedance path to the board’s power supply. Each ground
pin should likewise be provided with a low-impedance path to ground. The power supply pins drive
distinct groups of logic on chip. The VCC power supply should be bypassed to ground using at least four
0.1 F by-pass capacitors located as close as possible to the four sides of the package. The capacitor leads
and associated printed circuit traces connecting to chip VCC and ground should be kept to less than half an
inch per capacitor lead. A four-layer board is recommended, employing two inner layers as V
CC and GND
planes.
All output pins on the MPC8260 have fast rise and fall times. Printed circuit (PC) trace interconnection
length should be minimized in order to minimize overdamped conditions and reflections caused by these
fast output switching times. This recommendation particularly applies to the address and data buses.
Maximum PC trace lengths of six inches are recommended. Capacitance calculations should consider all
device loads as well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and
bypassing becomes especially critical in systems with higher capacitive loads because these loads create
higher transient currents in the VCC and GND circuits. Pull up all unused inputs or signals that will be
inputs during reset. Special care should be taken to minimize the noise levels on the PLL supply pins.
Table 5 provides preliminary, estimated power dissipation for various configurations. Note that suitable
thermal management is required for conditions above PD = 3W (when the ambient temperature is 70° C or
greater) to ensure the junction temperature does not exceed the maximum specified value. Also note that
the I/O power should be included when determining whether to use a heat sink.
Table 5. Estimated Power Dissipation for Various Configurations1
1 Test temperature = room temperature (25° C)
Bus
(MHz)
CPM
Multiplier
CPU
Multiplier
CPM
(MHz)
CPU
(MHz)
PINT (W)
2
2 P
INT = IDD x VDD Watts
Vddl
2.4
2.5
2.6
2.7
2.83
3 2.8 Vddl does not apply to HiP3 Rev C silicon.
33.3
4
133.3
2.04
2.14
2.26
2.38
2.50
50.0
2
3
100
150.0
2.21
2.30
2.45
2.59
2.69
66.7
2
2.5
133.3
166.7
2.47
2.62
2.74
2.88
3.02
66.7
2.5
166.7
2.57
2.69
2.83
2.98
3.12
66.7
2
3
133.3
200.0
2.81
2.95
3.12
3.29
3.43
66.7
2.5
3
166.7
200.0
2.88
3.05
3.22
3.38
3.55
50.0
3
4
150
200.0
2.83
3.00
3.14
3.31
3.48
Note:
相关PDF资料
PDF描述
FMC40DREN-S13 CONN EDGECARD 80POS .100 EXTEND
MC68HC000CEI10 IC MPU 16BIT 10MHZ 68-PLCC
IDT70V27S55PF IC SRAM 512KBIT 55NS 100TQFP
FMC40DREH-S13 CONN EDGECARD 80POS .100 EXTEND
MC68882EI40A IC FLOAT-PT COPROC 40MHZ 68PLCC
相关代理商/技术参数
参数描述
XPC8255CZUIFBC 功能描述:微处理器 - MPU POWERQUICC II HIP3 REV C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
XPC8255VVIFBC 功能描述:微处理器 - MPU PQ 2 HIP 3 NO-PB RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
XPC8255ZUIFBC 功能描述:微处理器 - MPU POWERQUICC II HIP3 REV C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
XPC8260ACZUKHBA 制造商:Freescale Semiconductor 功能描述:
XPC8260AZUKHBA 制造商:Motorola Inc 功能描述: