参数资料
| 型号： | XR16C2550IJ-F |
| 厂商： | Exar Corporation |
| 文件页数： | 23/37页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B DUAL 44PLCC |
| 标准包装： | 27 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
XR16C2550
3
REV. 1.0.2
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
PIN DESCRIPTIONS
Pin Description
NAME
40-PDIP
PIN #
44-PLCC
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
26
27
28
29
30
31
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the
internal registers in UART channel A/B during a data bus transac-
tion.
D7
D6
D5
D4
D3
D2
D1
D0
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
3
2
1
48
47
46
45
44
IO
Data bus lines [7:0] (bidirectional).
IOR#
21
24
19
I
Input/Output Read Strobe (active low). The falling edge instigates
an internal read cycle and retrieves the data byte from an internal
register pointed to by the address lines [A2:A0]. The data byte is
placed on the data bus to allow the host processor to read it on the
rising edge.
IOW#
18
20
15
I
Input/Output Write Strobe (active low). The falling edge instigates an
internal write cycle and the rising edge transfers the data byte on the
data bus to an internal register pointed by the address lines.
CSA#
14
16
10
I
UART channel A select (active low) to enable UART channel A in
the device for data bus operation.
CSB#
15
17
11
I
UART channel B select (active low) to enable UART channel B in
the device for data bus operation.
INTA
30
33
30
O
UART channel A Interrupt output. The output state is defined by the
user and through the software setting of MCR[3]. INTA is set to the
active mode and OP2A# output to a logic 0 when MCR[3] is set to a
logic 1. INTA is set to the three state mode and OP2A# to a logic 1
when MCR[3] is set to a logic 0 (default). See MCR[3].
INTB
29
32
29
O
UART channel B Interrupt output. The output state is defined by the
user and through the software setting of MCR[3]. INTB is set to the
active mode and OP2B# output to a logic 0 when MCR[3] is set to a
logic 1. INTB is set to the three state mode and OP2B# to a logic 1
when MCR[3] is set to a logic 0 (default). See MCR[3].
TXRDYA#
-
1
43
O
UART channel A Transmitter Ready (active low). The output pro-
vides the TX FIFO/THR status for transmit channel A. See Table 2.
If it is not used, leave it unconnected.
RXRDYA#
-
34
31
O
UART channel A Receiver Ready (active low). This output provides
the RX FIFO/RHR status for receive channel A. See Table 2. If it is
not used, leave it unconnected.
TXRDYB#
-
12
6
O
UART channel B Transmitter Ready (active low). The output pro-
vides the TX FIFO/THR status for transmit channel B. See Table 2.
If it is not used, leave it unconnected.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16C2850IM-F | IC UART FIFO 128B DUAL 48TQFP |
| XR16C2852IJ-F | IC UART FIFO 128B 44PLCC |
| XR16C850IMTR-F | IC UART FIFO 128B 48TQFP |
| XR16C854IQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR16C864IQ-F | IC UART FIFO 128B QUAD 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16C2550IM | 制造商:Exar Corporation 功能描述: |
| XR16C2550IM-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16C2550IMTR-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16C2550IP | 制造商:EXAR 制造商全称:EXAR 功能描述:2.97V TO 5.5V DUART WITH 16-BYTE FIFO |
| XR16C2552 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。