参数资料
型号: XR16C2850CJTR-F
厂商: Exar Corporation
文件页数: 23/51页
文件大小: 0K
描述: IC UART FIFO 128B 44PLCC
标准包装: 500
特点: *
通道数: 2,DUART
FIFO's: 128 字节
规程: RS232,RS485
电源电压: 2.97 V ~ 5.5 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.59x16.59)
包装: 带卷 (TR)
xr
XR16C2850
REV. 2.1.3
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
3
PIN DESCRIPTIONS
NAME
44-PLCC
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
29
30
31
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the inter-
nal registers in UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
9
8
7
6
5
4
3
2
3
2
1
48
47
46
45
44
I/O
Data bus lines [7:0] (bidirectional).
IOR#
24
19
I
Input/Output Read Strobe (active low). The falling edge instigates an
internal read cycle and retrieves the data byte from an internal register
pointed to by the address lines [A2:A0]. The data byte is placed on the
data bus to allow the host processor to read it on the rising edge.
IOW#
20
15
I
Input/Output Write Strobe (active low). The falling edge instigates an
internal write cycle and the rising edge transfers the data byte on the
data bus to an internal register pointed by the address lines.
CSA#
16
10
I
UART channel A select (active low) to enable UART channel A in the
device for data bus operation.
CSB#
17
11
I
UART channel B select (active low) to enable UART channel B in the
device for data bus operation.
INTA
33
30
O
UART channel A Interrupt output. The output state is defined by the
user through the software setting of MCR[3]. INTA is set to the active
mode and OP2A# output is LOW when MCR[3] is set to a logic 1. INTA
is set to the three state mode and OP2A# is HIGH when MCR[3] is set
to a logic 0 (default). See MCR[3]. If this output is not used, leave it
unconnected.
INTB
32
29
O
UART channel B Interrupt output. The output state is defined by the
user through the software setting of MCR[3]. INTB is set to the active
mode and OP2B# output is LOW when MCR[3] is set to a logic 1. INTB
is set to the three state mode and OP2B# is HIGH when MCR[3] is set
to a logic 0 (default). See MCR[3]. If this output is not used, leave it
unconnected.
TXRDYA#
1
43
O
UART channel A Transmitter Ready (active low). The output
provides the TX FIFO/THR status for transmit channel A. See
Table 2. If this output is not used, leave it unconnected.
RXRDYA#
34
31
O
UART channel A Receiver Ready (active low). This output provides the
RX FIFO/RHR status for receive channel A. See
Table 2. If this output
is not used, leave it unconnected.
TXRDYB#
12
6
O
UART channel B Transmitter Ready (active low). The output provides
the TX FIFO/THR status for transmit channel B. See
Table 2. If this
output is not used, leave it unconnected.
相关PDF资料
PDF描述
XR68C192IJ-F IC UART FIFI DUAL 44PLCC
XR68C92IJ-F DUAL CHANNEL UART 44PLCC
MS27484E12F98P CONN PLUG 10POS STRAIGHT W/PINS
XR16V564IL-F IC UART FIFO 32B QUAD 48QFN
MS27497E18A32P CONN RCPT 32POS WALL MNT W/PINS
相关代理商/技术参数
参数描述
XR16C2850CM 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16C2850CM-0A-EB 功能描述:UART 接口集成电路 Supports C2850 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16C2850CM-0B-EB 功能描述:UART 接口集成电路 Supports C2850 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16C2850CM48 制造商:EXAR 制造商全称:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850CM-F 功能描述:UART 接口集成电路 2.97V-5.5V 128B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel