- 您现在的位置：买卖IC网 > PDF目录11820 > XR16C854CVTR-F (Exar Corporation)IC UART FIFO 128B QUAD 64LQFP PDF资料下载
参数资料
| 型号： | XR16C854CVTR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 26/53页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 128B QUAD 64LQFP |
| 标准包装： | 1,000 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 128 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XR16C854/854D
32
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
REV. 3.1.0
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: Reserved
OP1# is not available as an output pin on the 854. But it is available for use during Internal Loopback Mode. In
the Loopback Mode, this bit is used to write the state of the modem RI# interface signal. If OP1# output is
required for RS485 operation, use the XR16C864.
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be set to a logic zero during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During loopback mode, it sets
OP2# internally to a logic 1.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During loopback mode, it sets OP2# internally
to a logic 0.
TABLE 13: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相关PDF资料 |
PDF描述 |
|---|---|
| ATUC64D3-Z2UR | IC MCU 32BIT 64KB FLASH 64VQFN |
| XR82C684J-F | IC UART CMOS QUAD 68PLCC |
| ST16C654IJ68-F | IC UART FIFO 64B QUAD 68PLCC |
| VE-B74-IW-F2 | CONVERTER MOD DC/DC 48V 100W |
| ST16C654CJ68-F | IC UART FIFO 64B QUAD 68PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16C854D | 制造商:EXAR 制造商全称:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO |
| XR16C854DCV | 制造商:Exar Corporation 功能描述: |
| XR16C854DCV-0A-EB | 功能描述:UART 接口集成电路 Supports C854D 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16C854DCV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16C854DCVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 128Byte FIFO 3.3V/5V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16C854DCVTR-F |
发布紧急采购，3分钟左右您将得到回复。