参数资料
| 型号： | XR16M2751IM48-F |
| 厂商： | Exar Corporation |
| 文件页数： | 13/53页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 48TQFP |
| 标准包装： | 250 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XR16M2751
20
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.0.0
2.19
Sleep Mode with Wake-Up Indicator and PowerSave Feature
The M2751 supports low voltage system designs, hence, a sleep mode with auto wake-up and PowerSave
feature is included to reduce power consumption when the device is not actively used.
2.19.1
Sleep Mode
All of these conditions must be satisfied for the M2751 to enter sleep mode:
■ no interrupts pending for both channels of the 2751 (ISR bit-0 = 1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M2751 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M2751 resumes normal operation by any of the following when PowerSave mode is disabled (pin 12 at
ground):
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the sleep mode is enabled and the 2751 is awakened by one of the conditions described above, an interrupt
is issued by the 2751 to signal to the CPU that it is awake. The lower nibble of the interrupt source register
(ISR) will read a value of 0x1 for this interrupt and reading the ISR clears this interrupt. Since the same value
(0x1) is also used to indicate no pending interrupt, users should exercise caution while using the sleep mode.
The 2751 will return to the sleep mode automatically after all interrupting conditions have been serviced and
cleared. If the 2751 is awakened by the modem inputs, a read to the MSR is required to reset the modem
inputs. In any case, the sleep mode will not be entered while an interrupt is pending from channel A or B. The
2751 will stay in the sleep mode of operation until it is disabled by setting IER bit-4 to a logic 0.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
2.19.2
PowerSave Feature
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
2751 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 43. If the input lines are floating or are toggling while the 2751 is in sleep mode, the
current can be up to 100 times more. If not using the PowerSave feature, then an external buffer would be
required to keep the address and data bus lines from toggling or floating to achieve the low current. But if the
PowerSave feature is enabled (pin 12 connected to VCC), this will eliminate the need for an external buffer by
internally isolating the address, data and control signals (see Figure 1 on page 1) from other bus activities that
could cause wasteful power drain. The 2751 enters PowerSave mode when pin 12 is connected to VCC and
the 2751 is in sleep mode (see Sleep Mode section above).
Since PowerSave mode isolates the address, data and control signals, the device will wake-up by:
■ a receive data start bit transition (HIGH to LOW)
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
The 2751 will return to the PowerSave mode automatically after a read to the MSR (to reset the modem inputs)
and all interrupting conditions have been serviced and cleared. The 2751 will stay in the PowerSave mode of
operation until it is disabled by setting IER bit-4 to a logic 0 and/or the PowerSave pin is connected to GND.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M2752IJ44-F | IC UART FIFO 64B DUAL 44PLCC |
| XR16M554IV64-F | IC UART FIFO 16B QUAD 64LQFP |
| XR16M564IJ68-F | IC UART FIFO 32B QUAD 68PLCC |
| XR16M570IL32-F | IC UART FIFO 16B 32QFN |
| XR16M580IM48-F | IC UART FIFO 16B 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M2752 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M2752_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M2752IJ-0A-EB | 功能描述:界面开发工具 Eval Board for XR16M2752IJ-0A RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M2752IJ-0B-EB | 功能描述:界面开发工具 Eval Board for XR16M2752IJ Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M2752IJ44 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。