- 您现在的位置：买卖IC网 > PDF目录11833 > XR16M564IV80-F (Exar Corporation)IC UART FIFO 32B QUAD 80LQFP PDF资料下载
参数资料
| 型号： | XR16M564IV80-F |
| 厂商： | Exar Corporation |
| 文件页数： | 27/55页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B QUAD 80LQFP |
| 标准包装： | 119 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 32 字节 |
| 规程： | RS232 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（12x12） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
XR16M564/564D
33
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
MCR[5]: Xon-Any Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the M564 is programmed to use the Xon/Xoff flow control.
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit-4 = 1)
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. The RX FIFO may need to be flushed upon enable. While in this mode, the infrared TX output
will be LOW during idle data conditions.
MCR[7]: Clock Prescaler Select (requires EFR bit-4 = 1)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
TABLE 14: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B5K-IX-F4 | CONVERTER MOD DC/DC 40V 75W |
| VE-B5K-IX-F3 | CONVERTER MOD DC/DC 40V 75W |
| VE-B5K-IX-F2 | CONVERTER MOD DC/DC 40V 75W |
| VE-B5K-IW-F4 | CONVERTER MOD DC/DC 40V 100W |
| VE-B5K-IW-F3 | CONVERTER MOD DC/DC 40V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M570 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO |
| XR16M570IB25 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO |
| XR16M570IB25-0C-EB | 功能描述:界面开发工具 Eval Board for XR16M570IB25 Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M570IB25-F | 功能描述:UART 接口集成电路 1.8 HIGH PERFORMANCE UART W/16 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M570IL24 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。