- 您现在的位置：买卖IC网 > PDF目录16556 > XR16M581IL32-0C-EB (Exar Corporation)EVAL BOARD FOR XR16M581-C 32QFN PDF资料下载
参数资料
| 型号： | XR16M581IL32-0C-EB |
| 厂商： | Exar Corporation |
| 文件页数： | 8/51页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M581-C 32QFN |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
XR16M581
16
1.62V TO 3.63V UART WITH 16-BYTE FIFO AND VLIO INTERFACE
REV. 1.0.1
2.10
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 12):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.11
Auto RTS Hysteresis
With the Auto RTS function enabled, an interrupt is generated when the receive FIFO reaches the selected RX
trigger level. The RTS# pin will not be forced HIGH (RTS off) until the receive FIFO reaches one trigger level
above the selected trigger level in the trigger table (Table 9). The RTS# pin will return LOW after the RX FIFO
is unloaded to one level below the selected trigger level. Under the above described conditions, the M581 will
continue to accept data until the receive FIFO gets full. The Auto RTS function is initiated when the RTS#
output pin is asserted LOW (RTS On).
TABLE 4: AUTO RTS (HARDWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
RTS# DE-ASSERTED (HIGH)
(CHARACTERS IN RX FIFO)
RTS# ASSERTED (LOW)
(CHARACTERS IN RX FIFO)
1
4
0
4
8
1
8
14
4
14
8
2.12
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 12):
Enable auto CTS flow control using EFR bit-7.
If needed, the CTS interrupt can be enabled through IER bit-7 (after setting EFR bit-4). The UART issues an
interrupt when the CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend
相关PDF资料 |
PDF描述 |
|---|---|
| ILC0603ERR10K | INDUCTOR CER 100NH 0603 |
| V48C8C100BF2 | CONVERTER MOD DC/DC 8V 100W |
| GSC10DRXI-S734 | CONN EDGECARD 20POS DIP .100 SLD |
| XR16M580IB25-0C-EB | EVAL BOARD FOR XR16M580-C 25BGA |
| H3AKH-1636G | IDC CABLE - HSC16H/AE16G/HPK16H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M581IL32-F | 功能描述:UART 接口集成电路 1.62-3.63V; 16-Byte FIFO & VLIO; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M598 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16M598IQ100 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16M598IQ100-F | 功能描述:UART 接口集成电路 8-ch 16-byte UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M654 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。