参数资料
| 型号： | XR16V2751IM-F |
| 厂商： | Exar Corporation |
| 文件页数： | 9/52页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 48TQFP |
| 标准包装： | 250 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.25 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
XR16V2751
17
REV. 1.0.1
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO AND POWERSAVE FEATURE
2.15
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 10):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
FIGURE 10. AUTO RTS AND CTS FLOW CONTROL OPERATION
The local UART (UARTA) starts data transfer by asserting RTSA# (1). RTSA# is normally connected to CTSB# (2) of
remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO
(4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and con-
tinues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA
monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows
(7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its trans-
mit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9),
UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until
next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB
with RTSB# and CTSA# controlling the data flow.
RTSA#
CTSB#
RXA
TXB
Transmitter
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Auto CTS
Monitor
RTSA#
TXB
RXA FIFO
CTSB#
Remote UART
UARTB
Local UART
UARTA
ON
OFF
ON
Suspend
Restart
RTS High
Threshold
Data Starts
ON
OFF
ON
Assert RTS# to Begin
Transmission
1
2
3
4
5
6
7
Receive
Data
RTS Low
Threshold
9
10
11
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Transmitter
Auto CTS
Monitor
RTSB#
CTSA#
RXB
TXA
INTA
(RXA FIFO
Interrupt)
RX FIFO
Trigger Level
RX FIFO
Trigger Level
8
12
RTSCTS1
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V2752IJ-F | IC UART FIFO 64B DUAL 44PLCC |
| XR16V554IVTR-F | IC UART FIFO 16B QUAD 64LQFP |
| XR16V564IJ-F | IC UART FIFO 32B QUAD 68PLCC |
| XR16V598IQ100-F | IC UART FIFO 16B OCTAL 100QFP |
| XR16V654DIV-F | IC UART FIFO 64B QUAD 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V2752 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16V2752_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16V2752IJ | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16V2752IJ-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V2752IJTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:XR16V2752IJTR-F |
发布紧急采购，3分钟左右您将得到回复。