参数资料
| 型号： | XR16V564IJ-F |
| 厂商： | Exar Corporation |
| 文件页数： | 13/54页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B QUAD 68PLCC |
| 标准包装： | 19 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 32 字节 |
| 规程： | RS232 |
| 电源电压： | 2.25 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 68-LCC（J 形引线） |
| 供应商设备封装： | 68-PLCC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
XR16V564/564D
20
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.4
2.14
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 16), the V564 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the V564 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the V564 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the V564 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to LOW. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 16) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the V564 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the V564 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The V564 sends the
Xoff-1,2 characters two-character-times (= time taken to send two characters at the programmed baud rate)
after the receive FIFO crosses the programmed trigger level. To clear this condition, the V564 will transmit the
programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the programmed
trigger level. Table 8 below explains this.
TABLE 8: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
30
30*
24
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters);
for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.15
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The V564 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to the RX FIFO and ISR bit-4 will be set to indicate detection of special character. Although the
Internal Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V598IQ100-F | IC UART FIFO 16B OCTAL 100QFP |
| XR16V654DIV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V698IQ100-F | IC UART FIFO 32B OCTAL 100QFP |
| XR16V794IV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V798IQ-F | IC UART FIFO 64B OCTAL 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V564IJTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:XR16V564IJTR-F |
| XR16V564IL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V564IL-0A-EVB | 功能描述:UART 接口集成电路 Supports V564 48 pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V564IL-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V564IV | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。