- 您现在的位置：买卖IC网 > PDF目录16433 > XR17C154CV-0A-EVB (Exar Corporation)EVAL BOARD FOR XR17C154-A 144TQF PDF资料下载
参数资料
| 型号： | XR17C154CV-0A-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 22/62页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR17C154-A 144TQF |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
xr
XR17C154
REV. 1.3.2
5V PCI BUS QUAD UART
29
4.3.3
Receiver Operation with FIFO
4.4
Automatic Hardware (RTS/CTS or DTR/DSR) Flow Control Operation
Automatic hardware RTS/CTS or DTR/DSR flow control is used to prevent data overrun to the local receiver
FIFO and remote receiver FIFO. The RTS#/DTR# output pin is used to request the remote unit to suspend/
restart data transmission while the CTS#/DSR# input pin is monitored to suspend/restart the local transmitter.
The auto RTS/CTS or DTR/DSR flow control features are individually selected to fit specific application
requirement and enabled through EFR bit-6 and 7 and MCR bit-2 for either RTS/CTS or DTR/DSR control
signals.
Auto RTS flow control must be started by asserting the RTS# output pin LOW (MCR bit-1 = 1). Similarly, Auto
DTR flow control must be started by asserting the DTR# output pin LOW (MCR bit-0 = 1). Figure 14 shows in
detail how automatic hardware flow control works.
FIGURE 13. RECEIVER OPERATION IN FIFO AND FLOW CONTROL MODE
TABLE 10: AUTO RTS/CTS OR DTR/DSR FLOW CONTROL SELECTION
MCR BIT-2
EFR BIT-7
EFR BIT-6
HARDWARE FLOW CONTROL SELECTION
0
1
X
Auto CTS Flow Control Enabled
0
X
1
Auto RTS Flow Control Enabled
1
X
Auto DSR Flow Control Enabled
1
X
1
Auto DTR Flow Control Enabled
X
0
No Hardware Flow Control
Receive Data Shift
Register (RSR)
RXFIFO1
16X or 8X Sampling
Clock (8XMODE Reg.)
E
rror
Fl
ag
s
(64-s
ets)
E
rro
rFl
ags
i
n
LS
R
bi
ts
4:2
64 bytes by 11-
bit wide FIFO
Receive Data Characters
FIFO Trigger=48
Example:
- FIFO trigger level set at 48 bytes
- RTS/DTR hyasteresis set at +/-8 chars.
Data fills to 56
Data falls to 40
Data Bit
Validation
Receive Data
FIFO
(64-byte)
Receive
Data
Receive Data
Byte and Errors
RHR Interrupt (ISR bit-2) is programmed
at FIFO trigger level (RXTRG).
FIFO is Enable by FCR bit-0=1
RTS#/DTR# de-asserts when data fills above
the trigger level to suspend remote transmitter.
Enable by EFR bit-6=1, MCR bit-2.
RTS#/DTR# re-asserts when data falls below
the trigger level to restart remote transmitter.
Enable by EFR bit-6=1, MCR bit-2.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V798IQ-0B-EVB | EVAL BOARD FOR XR16V798-B 100QFP |
| XR16V798IQ-0A-EVB | EVAL BOARD FOR XR16V798-A 100QFP |
| XR16V698IQ-0B-EVB | EVAL BOARD FOR XR16V698-B 100QFP |
| XR16V698IQ-0A-EVB | EVAL BOARD FOR XR16V698-A 100QFP |
| KIT33972AEWEVBE | KIT EVALUATION FOR MC33972 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR17C154CV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154CVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C154CVTR-F |
| XR17C154IV | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154IV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154IVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C154IVTR-F |
发布紧急采购，3分钟左右您将得到回复。