参数资料
型号: XR20M1170IG16
厂商: Exar Corporation
文件页数: 14/56页
文件大小: 0K
描述: IC UART FIFO I2C/SPI 64B 16TSSOP
产品变化通告: Leaded UART, V&I Obsolescence 11/Apr/2011
标准包装: 95
特点: *
通道数: 1,UART
FIFO's: 64 字节
规程: RS485
电源电压: 2.25 V ~ 3.6 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 管件
XR20M1170
21
REV. 1.1.0
I2C/SPI UART WITH 64-BYTE FIFO
2.16
Sleep Mode with Auto Wake-Up
The M1170 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the M1170 to enter sleep mode:
no interrupts pending for the M1170 (ISR bit-0 = 1)
sleep mode of both channels are enabled (IER bit-4 = 1)
modem inputs are not toggling (MSR bits 0-3 = 0)
RX input pin is idling HIGH
The M1170 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M1170 resumes normal operation by any of the following:
a receive data start bit transition (HIGH to LOW)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M1170 is awakened by any one of the above conditions, it will return to the sleep mode automatically
after all interrupting conditions have been serviced and cleared. If the M1170 is awakened by the modem
inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be
entered while an interrupt is pending. The M1170 will stay in the sleep mode of operation until it is disabled by
setting IER bit-4 to a logic 0.
If the serial clock, serial data, and modem input lines remain steady when the M1170 is in sleep mode, the
maximum current will be in the microamp range as specified in the DC Electrical Characteristics on page 41.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX input idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition upon the
restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type) are also put
to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a 47k-100k
ohm pull-up resistor on the RX input pin.
相关PDF资料
PDF描述
MS27472P12B22S CONN RCPT 22POS WALL MT W/SCKT
V24B28H150BL CONVERTER MOD DC/DC 28V 150W
VI-B7K-IW-F3 CONVERTER MOD DC/DC 40V 100W
MS27467E17F8P CONN PLUG 8POS STRAIGHT W/PINS
MS27473E14B15SB CONN PLUG 15POS STRAIGHT W/SCKT
相关代理商/技术参数
参数描述
XR20M1170IG16-F 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR20M1170IG16-F 制造商:Exar Corporation 功能描述:IC SGL UART 16MBPS 3.63V 16-TSSOP 制造商:Exar Corporation 功能描述:IC, SGL UART, 16MBPS, 3.63V, 16-TSSOP
XR20M1170IG16TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 64Byte FIFO 1.8V/2.5V/3.3V 16-Pin TSSOP T/R 制造商:Exar Corporation 功能描述:XR20M1170IG16TR-F 制造商:EXAR 功能描述:UART 1-CH 64Byte FIFO 1.8V/2.5V/3.3V 16-Pin TSSOP T/R
XR20M1170IG24 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR20M1170IG24-F 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel