- 您现在的位置：买卖IC网 > PDF目录11834 > XR68C92CV-F (Exar Corporation)DUAL CHANNEL UART 44LQFP PDF资料下载
参数资料
| 型号： | XR68C92CV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 6/33页 |
| 文件大小： | 0K |
| 描述： | DUAL CHANNEL UART 44LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
XR68C92/192
14
Rev. 1.33
command register) and the CPU cannot stop it. When
the stop command is issued (by reading the stop C/T
command register), the CPU only resets the C/T inter-
rupt. This mode allows the C/T to be used as a
programmable clock source for channels A and B (see
CSRA, CSRB register), and/or a periodic interrupt
generator. In this mode, the C/T generates a square-
wave output (see Figure 2) derived from the pro-
grammed timer input clock source. The square wave
generated by the timer has a period of 2 X (pre-load
value) X (period of clock source) and is available as a
clock source for both channels A and B. Since the timer
cannot be stopped, the values in the registers
(CUR:CLR) should not be read. See description of
ACR register to see how to choose clock source for the
C/T.
When the start counter command register (STCR,
address 0xE) is read, the C/T terminates the current
countdown sequence and sets its output to a '1' (OP3
can be programmed to show this output). The C/T is
then initialized to the pre-load value, and begins a new
countdown sequence. When the terminal count is
reached (0x0000), the C/T sets its output to a '0'. Then,
it gets re-initialized to the pre-load value and repeats
the countdown sequence. See Figure 2 for the result-
ing waveform.
The timer sets the C/T-ready bit in the interrupt status
register (ISR Bit-3) every other time it reaches the
terminal count (at every rising edge of the output).
Users can program the timer to generate an interrupt
request for this condition (every second countdown
cycle) on the -INT output. If the CPU changes the pre-
load value, the timer will not recognize the new value
until either
(a) it reaches the next terminal count and is reinitialized
automatically, or
(b) it is forced to re-initialize by a start command.
When a read at the stop counter command address is
performed, the timer clears ISR Bit-3 but does not stop.
Because in timer mode the C/T runs continuously, it
should be completely configured (pre-load value
loaded and start counter command issued) before
programming the timer output to appear on OP3.
OTHER PROGRAMMING REMARKS
The contents of internal registers should not be
changed during receiver/transmitter operation as cer-
tain changes can produce undesired results. For ex-
ample, changing the number of bits per character while
the transmitter is active will result in transmitting an
incorrect character. The contents of the clock-select
register (CSR) and ACR Bit-7 should only be changed
after the receiver(s) and transmitter(s) have been
issued software RX and TX reset commands. Simi-
larly, changes to the auxiliary control register (ACR Bits
4-6) should only be made while the counter/timer (C/T)
is not used.
The mode registers of each channel MR0, MR1 and
MR2 are accessed via an auxiliary pointer. The pointer
is set to mode register one (MR1) by RESET. It can be
set to MR0 or MR1
by issuing a “reset pointer”
command (0xB0 or 0x10 respectively) via the
channel's command register. Any read or write of the
mode register switches the pointer to next mode reg-
ister. All accesses subsequent to reading/writing MR1
will address MR2 unless the pointer is reset to MR0 or
MR1 as described above. The mode, command,
clock-select, and status registers are duplicated for
each channel to allow independent operation and
control (except that both channels are restricted to
baud rates that are in the same set).
相关PDF资料 |
PDF描述 |
|---|---|
| XR88C192IJ-F | IC UART FIFO DUAL 44PLCC |
| VI-JWJ-IW-F3 | CONVERTER MOD DC/DC 36V 100W |
| XR88C681P/40-F | IC UART CMOS DUAL 40PDIP |
| MS27472T16B8PA | CONN RCPT 8POS WALL MT W/PINS |
| MS27473E12F8PA | CONN PLUG 8POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR68C92CVTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68C92IJ | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR68C92IJ-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68C92IJTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68C92IP | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
发布紧急采购，3分钟左右您将得到回复。