参数资料
| 型号： | XR68M752IL32TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 13/54页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 32QFN |
| 标准包装： | 3,000 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
XR16M752/XR68M752
20
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
2.15
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 15), the M752 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the M752 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the M752 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the M752 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the M752 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the M752 automatically
sends the Xoff-1,2 via the serial TX output to the remote modem when the RX FIFO reaches the Halt Level
(TCR[3:0]). To clear this condition, the M752 will transmit the programmed Xon-1,2 characters as soon as RX
FIFO falls down to the Resume Level.
2.16
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The M752 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the Internal
Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of bits is
dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison.
2.17
Infrared Mode
The M752 UART includes the infrared encoder and decoder compatible to the IrDA (Infrared Data Association)
version 1.0. The IrDA 1.0 standard that stipulates the infrared encoder sends out a 3/16 of a bit wide HIGH-
pulse for each “0” bit in the transmit data stream. This signal encoding reduces the on-time of the infrared LED,
hence reduces the power consumption. See Figure 12 below.
The infrared encoder and decoder can be enabled by setting DLD register bit-7 to a ‘1’. When the infrared
feature is enabled, the transmit data output, TX, idles LOW. Likewise, the RX input also idles LOW, see
Figure 12. In the 49-pin STBGA package, this feature can be enabled upon power-up by connecting the
ENIR# pin of the STBGA package to GND. If the IR mode is enabled via the ENIR# pin, it can be disabled
after power-up via DLD bit-7.
The wireless infrared decoder receives the input pulse from the infrared sensing diode on the RX pin. Each
time it senses a light pulse, it returns a logic 1 to the data bit stream.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA168-15AT | MCU AVR 16K FLASH 15MHZ 32-TQFP |
| ST16C450CQ48TR-F | IC UART SINGLE 48TQFP |
| ST16C450IJ44TR-F | IC UART SINGLE 44PLCC |
| XR16M770IL24-F | IC UART FIFO 64B 24QFN |
| XR16M680IL32-F | IC UART FIFO 32B 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR68M752IM-0B-EB | 功能描述:界面开发工具 Support XR68M752 48L TQFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR68M752IM48 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR68M752IM48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68M752IM48TR-F | 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48 |
| XR7090AA-BC-0001 | 制造商:CREE 制造商全称:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling |
发布紧急采购，3分钟左右您将得到回复。