- 您现在的位置：买卖IC网 > PDF目录11834 > XR88C192CJ-F (Exar Corporation)IC UART FIFO DUAL 44PLCC PDF资料下载
参数资料
| 型号： | XR88C192CJ-F |
| 厂商： | Exar Corporation |
| 文件页数： | 5/32页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO DUAL 44PLCC |
| 标准包装： | 27 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 管件 |
| 其它名称： | XR88C192CJ-F-ND |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
XR88C92/192
13
Rev. 1.33
Users can program the counter to generate an interrupt
request for this condition on the -INT output by
unmasking the bit-3 in the Interrupt Mask Register (IMR,
address 0x5). After 0x0000 the count becomes
0xFFFF, and the counter continues counting down from
there. If the CPU changes the pre-load value, the
counter will not recognize the new value until it receives
the next start counter command (and is reinitialized).
When a read at the stop counter command register
(address 0xF) is performed, the counter stops the
countdown sequence and clears ISR Bit-3. The count
value should only be read while the counter is stopped
because only one of the count registers (either CUR, at
address 0x6 or CLR, at address 0x7) can be read at a
time. If the counter is running, a decrement of CLR that
requires a borrow from the CUR could take place
between the two register reads. Figure 2 shows the
C/T output in the counter mode. OP3 can be pro-
grammed to show the C/T output.
In addition to the watch dog timer described above, the
C/T can be used for receive timeout function (see
description under CRA, CRB in the registers section
also). The C/T is more accurate and the timeout period
is programmable unlike the watchdog timer. However,
only one channel can use the C/T for receive timeout at
any given time. The C/T timeout mode uses the received
data stream to start the counter. Each time a character
is shifted from the receive shift register to the receive
FIFO, the C/T is reloaded with the programmed value in
CTPU and CTPL and it restarts on the next C/T clock.
If a new character is not received before the C/T reaches
terminal count (= 0x0000), a counter ready interrupt
(ISR bit-3) is generated. The user can appropriately
program the CTPU and CTPL for the desired timeout
period. Typically this is slightly more than one character
time. Note that if C/T is used for receiver timeout, a
counter ready interrupt is generated whereas if the
watchdog timer is used, a receiver ready interrupt is
generated.
TIMER MODE
In the timer mode, the C/T runs continuously once the
start command is issued (by reading the start C/T
command register) and the CPU cannot stop it. When
the stop command is issued (by reading the stop C/T
command register), the CPU only resets the C/T inter-
rupt. This mode allows the C/T to be used as a program-
mable clock source for channels A and B (see CSRA,
CSRB register), and/or a periodic interrupt generator. In
this mode, the C/T generates a square-wave output (see
Figure 2) derived from the programmed timer input
clock source. The square wave generated by the timer
has a period of 2 X (pre-load value) X (period of clock
source) and is available as a clock source for both
channels A and B. Since the timer cannot be stopped,
the values in the registers (CUR:CLR) should not be
read. See description of ACR register to see how to
choose clock source for the C/T.
When the start counter command register (STCR,
PRELOAD
VALUE
TERMINAL
COUNT
C/T OUTPUT IN
COUNTER MODE
C/T OUTPUT IN
TIMER MODE
PRELOAD
VALUE
TERMINAL
COUNT
PRELOAD
VALUE
TERMINAL
COUNT
PRELOAD
VALUE
PRELOAD
VALUE
TERMINAL
COUNT
TERMINAL
COUNT
TERMINAL
COUNT
PRELOAD
VALUE
PRELOAD
VALUE
START C/T COMMAND
ISSUED
PRELOAD
VALUE
TERMINAL
COUNT
Figure 2: C/T output in Timer and Counter modes.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27508E12A22SA | CONN RCPT 22POS BOX MNT W/SCKT |
| MS27497E16B55P | CONN RCPT 55POS WALL MNT W/PINS |
| XR68C92CV-F | DUAL CHANNEL UART 44LQFP |
| XR88C192IJ-F | IC UART FIFO DUAL 44PLCC |
| VI-JWJ-IW-F3 | CONVERTER MOD DC/DC 36V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR88C192CP | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CV | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CV-0A-EVB | 功能描述:界面开发工具 Supports 88C192 44ld TQFP, ISA Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR88C192CV-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C192IJ | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
发布紧急采购，3分钟左右您将得到回复。