参数资料
| 型号： | XRA1403IL24-F |
| 厂商： | Exar Corporation |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER SPI 16B 24QFN |
| 标准包装： | 490 |
| 接口： | SPI |
| 输入/输出数： | 16 |
| 中断输出： | 是 |
| 频率 - 时钟： | 26MHz |
| 电源电压： | 1.65 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 托盘 |
| 其它名称： | 1016-1724 |
XRA1403
7
REV. 1.0.0
16-BIT SPI GPIO EXPANDER WITH RESET INPUT
2.0 REGISTER DESCRIPTION
2.1
GPIO State Register 1 (GSR1) - Read-Only
The status of P7 - P0 can be read via this register. A read will show the current state of these pins (or the
inverted state of these pins if enabled via the PIR Register). Reading this register will clear an input interrupt
(see Table 3 for complete details). Reading this register will also return the last value written to the OCR
register for any pins that are configured as outputs (ie. this is not the same as the state of the actual output pin
since the output pin can be in three-state mode). A write to this register has no effect. The MSB of this register
corresponds with P7 and the LSB of this register corresponds with P0.
2.2
GPIO State Register 2 (GSR2) - Read-Only
The status of P15 - P8 can be read via this register. A read will show the current state of these pins (or the
inverted state of these pins if enabled via the PIR Register). Reading this register will clear an input interrupt
(see Table 3 for complete details). Reading this register will also return the last value written to the OCR
register for any pins that are configured as outputs (ie. this is not the same as the state of the actual output pin
since the output pin can be in three-state mode). A write to this register has no effect. The MSB of this register
corresponds with P15 and the LSB of this register corresponds with P8.
2.3
Output Control Register 1 (OCR1) - Read/Write
When P7 - P0 are defined as outputs, they can be controlled by writing to this register. Reading this register
will return the last value written to it, however, this value may not be the actual state of the output pin since
these pins can be in three-state mode. The MSB of this register corresponds with P7 and the LSB of this
register corresponds with P0.
2.4
Output Control Register 2 (OCR2) - Read/Write
When P15 - P8 are defined as outputs, they can be controlled by writing to this register. Reading this register
will return the last value written to it, however, this value may not be the actual state of the output pin since
these pins can be in three-state mode. The MSB of this register corresponds with P15 and the LSB of this
register corresponds with P8.
2.5
Input Polarity Inversion Register 1 (PIR1) - Read/Write
When P7 - P0 are defined as inputs, this register inverts the polarity of the input value read from the Input Port
Register. If the corresponding bit in this register is set to ’1’, the value of this bit in the GSR Register will be the
inverted value of the input pin. If the corresponding bit in this register is set to ’0’, the value of this bit in the
GSR Register will be the actual value of the input pin. The MSB of this register corresponds with P7 and the
LSB of this register corresponds with P0.
2.6
Input Polarity Inversion Register 2 (PIR2) - Read/Write
When P15 - P8 are defined as inputs, this register inverts the polarity of the input value read from the Input Port
Register. If the corresponding bit in this register is set to ’1’, the value of this bit in the GSR Register will be the
inverted value of the input pin. If the corresponding bit in this register is set to ’0’, the value of this bit in the
GSR Register will be the actual value of the input pin. The MSB of this register corresponds with P15 and the
LSB of this register corresponds with P8.
2.7
GPIO Configuration Register 1 (GCR1) - Read/Write
This register configures the GPIOs as inputs or outputs. After power-up and reset, the GPIOs are inputs.
Setting these bits to ’0’ will enable the GPIOs as outputs. Setting these bits to ’1’ will enable the GPIOs as
inputs. The MSB of this register corresponds with P7 and the LSB of this register corresponds with P0.
2.8
GPIO Configuration Register 2 (GCR2) - Read/Write
This register configures the GPIOs as inputs or outputs. After power-up and reset, the GPIOs are inputs.
Setting these bits to ’0’ will enable the GPIOs as outputs. Setting these bits to ’1’ will enable the GPIOs as
inputs. The MSB of this register corresponds with P15 and the LSB of this register corresponds with P8.
相关PDF资料 |
PDF描述 |
|---|---|
| XRA1404IL16-F | IC I/O EXPANDER SPI 8B 16QFN |
| XRA1405IL24-F | IC I/O EXPANDER SPI 16B 24QFN |
| XRM48L950ZWTT | MCU 16/32Bit FLASH 3MB 337NFBGA |
| XRT59L91ID-F | IC LIU E1 SGL 3.3V 16SOIC |
| XRT59L921IB | IC LIU E1 21CH 316STBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRA1403IL24TR-F | 功能描述:接口-I/O扩展器 16 Bit SPI GPIO Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| XRA1404IG16-0B-EB | 功能描述:其他开发工具 8 Bit SPI Eval GPIO Expander RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| XRA1404IG16-F | 功能描述:接口-I/O扩展器 8 Bit SPI GPIO Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| XRA1404IG16TR-F | 功能描述:接口-I/O扩展器 8 Bit SPI GPIO Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| XRA1404IL16-0B-EB | 功能描述:其他开发工具 8 Bit SPI Eval GPIO Expander RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。