- 您现在的位置：买卖IC网 > PDF目录20774 > XRP6840AILB-F (Exar Corporation)IC LED FLASH DVR I2C 20TQFN PDF资料下载
参数资料
| 型号： | XRP6840AILB-F |
| 厂商： | Exar Corporation |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | IC LED FLASH DVR I2C 20TQFN |
| 特色产品： | XRP6840 4.3 A Flash LED Driver |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 3 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 2MHz ~ 2.8MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN（4x4） |
| 包装： | 散装 |
| 工作温度： | -40°C ~ 85°C |
| 配用： | 1016-1337-ND - EVAL BOARD FOR XRP6840 |
| 其它名称： | 1016-1335 |
X R P 6 8 4 0
4 . 3 A S u p e r c a p a c i t o r F l a s h L E D D r i v e r w i t h I 2 C
THEORY OF OPERATION
When V IN reaches 2.7V during initial power up,
a power on reset signal will be issued to reset
all the registers and the internal logic, and the
system will be ready for operation.
To be in operation the XRP6840 must be
enabled through RESET_N, pin 6. The LEDs
can be activated through LEDFLASH or
LEDTORCH registers.
C HARGE P UMP M ODES 1 X , 1.5 X AND 2 X
The XRP6840 charge pump can operate in 1x,
1.5x and 2x modes to ensure desired current
regulation. Once the output reaches V OUT_LIMIT ,
the charge pump will turn off.
In 1x mode, the input is simply connected to
the output through an internal 0.5 Ω MOSFET.
An internal in-rush current limit will keep the
charging current controlled to a maximum of
600mA.
In 1.5x mode, during the first clock phase the
2 flying capacitors, C 1 and C 2 , are series
connected between V IN and ground, charging
each capacitor to ? V IN . In the second clock
phase, the flying capacitors are parallel
connected and placed in series with V IN ,
producing 1.5xV IN to be discharged across the
output capacitor. Note the maximum total
output current is now 600mA÷1.5 or 400mA.
In 2x mode, during the first clock phase, one
flying capacitors is charged to V IN . In the
second clock phase, this capacitor is placed in
series with V IN , producing 2xV IN to be
discharged across the output capacitor. Note
further in the High Efficiency Torch Mode
section.
The XRP6840 can operate in either “Auto Gain
Mode” or “Programmable Gain Mode”.
However, either mode will be overridden
during start-up based on the following internal
control algorithm:
1. If V OUT > VOUT_LIMIT then the charge pump is
OFF.
2. If V OUT < V IN – 1V then the charge pump
can only operate in 1x mode.
3. If V IN – 1V < V OUT < V IN then the charge
pump is allowed to operate in either 1x or
1.5x mode but not in 2x mode.
4. If V OUT > V IN then the charge pump can
operate either in 1.5x or 2x mode but not
in 1x mode (there is no reverse current
limit on the 0.5 Ω bypass MOSFET).
5. If V OUT > V OUT_LIMIT , and all LEDs are
deactivated then XRP6840 will operate in
standby mode with 30μA supply current.
V OUT_LIMIT is 4.5V for Torch Mode and High
Efficiency Torch Mode; for Flash mode
V OUT_LIMIT is shown in Table 4.
Standby mode is set by either LEDFLASH or
LEDTORCH registers [B7 B6 B5] to [0 0 0].
This will deactivate all the LED channels.
A UTO G AIN S TART - UP
The Auto Gain Start mode is the fastest way to
charge the output toward VOUT_LIMIT. It is
initiated with the following conditions; as
shown in Table 7 (a sub-set of Table 2), in
STATUS1 Register.
the maximum total output current is now
600mA÷2 or 300mA.
C HARGE P UMP C ONTROLLER
B7
0
1
1
B6
1
0
1
B4
0
0
0
B3
0
0
0
Operation Mode
High Efficiency Torch Mode
Auto Gain Start Torch Mode
Auto Gain Start Flash Mode
The charge pump controller regulates the
output by turning the charge pump off once
the output reaches V OUT_LIMIT . For both Torch
and Flash Modes, there is 50mV of output
voltage hysteresis before the charge pump is
re-enabled. However, in High Efficiency Torch
mode, it will only turn on again when V LEDX is
below the drop out voltage of approximately
0.36V. Once the charge pump turns on again,
it will then monitor both V OUT and V LEDX
voltages. This operation will be explained
Table 7: Auto Start Mode from STATUS1 Register
When in Auto Gain Start Mode, the XRP6840
will charge up V OUT to V OUT_LIMIT with maximum
available current within the constraints defined
above for start-up.
In this mode the XRP6840 will initialize the
system as follows:
1. Turn off all the LEDs that were
programmed through LEDTORCH or
LEDFLASH registers.
? 2009 Exar Corporation
12/17
Rev. 1.0.0
相关PDF资料 |
PDF描述 |
|---|---|
| SWS1000L-24 | PWR SUP MED 24V 44A SGL OUTPUT |
| CS8221YDP3G | IC REG LDO 5V .1A D2PAK-3 |
| GBM12DSAS | CONN EDGECARD 24POS R/A .156 SLD |
| VE-J1X-CW-S | CONVERTER MOD DC/DC 5.2V 100W |
| TAJV108K006RNJ | CAP TANT 1000UF 6.3V 10% 2924 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRP6840AILBTR-F | 功能描述:LED照明驱动器 4.3A Supercap. Flash 3-Ch LED Drivr w/I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| XRP6840BILB-F | 功能描述:LED照明驱动器 4.3A Supercap. Flash 2-Ch LED Drivr w/I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| XRP6840BILBTR-F | 功能描述:LED照明驱动器 4.3A Supercap. Flash 2-Ch LED Drivr w/I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| XRP6840EVB | 功能描述:LED 照明开发工具 Eval Board for XRP6840 Series RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| XRP7410EH-F | 功能描述:开关变换器、稳压器与控制器 Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。