- 您现在的位置：买卖IC网 > Datasheet目录1013 > XRP7604EVB (Exar Corporation)EVAL BOARD FOR XRP7604 Datasheet资料下载
参数资料
| 型号： | XRP7604EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XRP7604 |
| 标准包装： | 1 |
| 系列： | * |
X R P 7 6 0 4
1 A 2 9 V N o n - S y n c . B u c k H i g h P o w e r L E D D r i v e r
Equ.3: L =
Vo × ( Vin ? Vo )
Vin × f × Δ I L
Ceramic capacitors are recommended for input
filtering due to their low Equivalent Series
Resistance (ESR), Equivalent Series
Equ.5 : If ≥ 1 ?
× Io
Where Vin is converter input voltage and Vo is
converter output voltage. Since voltage across
Rset is small, Vo approximately equals Vf (for
a string of series connected LEDs Vo equals
total Vf)
Δ I L is inductor current ripple (nominally set to
30% of Io)
Inductor Isat and Irms must allow sufficient
safeguard over output current Io. As a rule of
thumb these parameters should be 50%
higher than Io. Where high efficiency is
required a low DCR inductor should be used.
I NPUT CAPACITOR SELECTION
Select the input capacitor for capacitanceand
ripple current rating. Use the capacitances
listed in the table 1 as a starting point and if
needed increase Cin.
inductance (ESL) and small form factor.
S CHOTTKY RECTIFIER SELECTION
Select the Schottky D1 for Voltage rating VR
and current rating If. Recommended schottky
diode voltage rating for 12V and 24V
applications is 30V and 40V respectively.
Current rating can be calculated from:
Vo
Vin
Note that in applications where duty cycle is
low, Schottky losses comprise a larger
percentage of converter losses. In order to
improve the efficiency in these applications
choose a Schottky that meets the calculated
current rating and has a lower Vf.
F EEDBACK RESISTOR RFB
I O (A)
<0.7
0.71 to 1.2
>1.2
Cin (μF)
2.2
4.7
2 x 4.7
R2 is part of XRP7604 loop compensation
network. Use a 30k R2 for Vin of 20V and
larger. Use R2 of 60K for Vin less than 20V.
Table 1: Cin Selection
Calculate the ripple current requirement from:
Equ.4: Irip = Io × D × ( 1 ? D )
C APACITOR C5
This is the decoupling capacitor for the power
supply for the internal driver. Use a 0.1uF and
place as closely to VDR and SVIN pins as
possible.
Where D =
Vo
Vin
? 2009 Exar Corporation
10/13
Rev. 1.0.0
相关PDF资料 |
PDF描述 |
|---|---|
| XRP7620EVB | EVAL BOARD FOR XRP7620 |
| XT374S15 | RELAY GEN PURPOSE SPDT 16A 115V |
| Y0054140K253T29L | RES 140.253K OHM .5W .01% AXIAL |
| REC5-0505SRW/H2/A/M/SMD | DC/DC转换器 5W DC/DC 2kV REG 2:1 4.5-9Vin 5Vout |
| Y0065321R00T0L | RES 321 OHM 3W .01% FOIL RAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRP7613EVB | 功能描述:LED 照明开发工具 XRP7613 Eval Brd RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| XRP7613IDBTR-F | 功能描述:LED照明驱动器 1.2A 36V SD High Brightness LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| XRP7618 | 制造商:EXAR 制造商全称:EXAR 功能描述:8-Channel Constant Current Linear LED Driver With Smart TalkTM |
| XRP7618EVB | 功能描述:LED 照明开发工具 XRP7618 EVAL 8CH LED DRIVER BRD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| XRP7618IGB-F | 功能描述:LED照明驱动器 8CH LED DRIVER,CNST CURRENT, 100mA/CHNL RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。