参数资料
| 型号： | XRT5794IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1 QUAD 80TQFP |
| 产品变化通告： | Product Discontinuation 18/Jan/2012 |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | E1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-TQFP（14x14） |
| 包装： | 托盘 |
XR-T5794
12
Rev. 2.01
SYSTEM DESCRIPTION
This device is a quad E1 transceiver which provides
electrical interface for 2.048Mbps applications. Its unique
architecture includes four receiver circuits that convert
CCITT G.703 compliant bipolar signals to TTL compatible
logic levels.
Likewise, in the other direction, four
transmitters translate TTL compatible logic levels to
G.703 compatible bipolar signals.
A fifth transmitter
circuit is used as a monitor output. One of the four AMI
receiver inputs or transmitter outputs can be selected (via
MONSEL[2..0] lines) to be monitored. The MOUT output
can be disabled using the MONEN signal.
This device supports two different types of loopback
functions. Each of four channels can be independently
looped either in local or remote sides digitally. The
remote loopback is performed between the receiver input
and transmitter output. To activate the remote loopback
on channel n, LOOPENn and LPMODn inputs are driven
high. Local loopback on channel n, can be established
similarly by driving LOOPENn high and clearing LPMODn
inputs.
More than one channel can be tested
simultaneously.
RECEIVERS
Each of the four identical E1 line receivers will accept
bipolar signals meeting the CCITT G.703 pulse mask
requirements.
Each input stage consists of a slicing
circuitry which samples the incoming pulses at a fixed
percentage of the signals maximum amplitude.
The
slicing voltage level is generated using a precision peak
detector. The receiver section can tolerate up to 12dB of
line loss (measured at 1.024MHz).
A loss of signal (LOS) is detected on any inputs by input
fail circuitry. There is an independent LOS pin dedicated
for each of the receivers. The LOS detection is based on
signal energy instead of number of zeros.
A balanced signal (100
or 120) must be coupled by a
transformer. An unbalanced signal (75
) may be coupled
via a capacitor or transformer coupled.
TRANSMITTERS
This device contains five identical CCITT G.703
compliant transmitters which meet the return loss
requirements. Each transmitter is a single-ended voltage
driver.
External resistors are used to maintain an
accurate source impedance that has a high return loss to
the transformer or the capacitor. Each of the drivers can
be individually disabled, this is required in fault tolerant
applications where redundancy is a requirement. During
power-down mode of operation the bipolar outputs can be
disabled.
To protect the data integrity during a brownout, the output
pulse amplitudes are reduced by a factor of 25% if the
supply drops below an internally set limit.
Transmission is possible either with or without a clock. If a
clock is used, the transmit input data must consist of
full-width NRZ pulses, and the transmitter output pulse
width is determined by the duty cycle of the clock. If the
transmit clock is tied high, the transmitter output pulses
are determined by the input data pulse width. In this
mode, RZ data must be supplied to the device.
TXP TXN
RX
TX
RXP RXN
RXIN
TXOUT
Remote Loopback
TXP TXN
RX
TX
RXP RXN
RXIN
TXOUT
Local Loopback
LPMOD=0
LPEN=1
Figure 5. Loopback Configurations
LPMOD=1
LPEN=1
相关PDF资料 |
PDF描述 |
|---|---|
| XRT5894IVTR-F | IC LIU E1 QUAD 64TQFP |
| XRT5897IV-F | IC LIU E1 7CH 3.3V 100TQFP |
| XRT5997IV-F | IC LIU E1 7CH 3.3V 100TQFP |
| XRT6164AIP-F | IC TXRX DGTL INTERFACE 16PDIP |
| XRT6164CD-F | IC TXRX DGTL INTERFACE 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT5795IJ-F | 功能描述:外围驱动器与原件 - PCI Quad E1 LIU RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT5795IV | 功能描述:LIN 收发器 Quad E-1 LIU RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| XRT5795IV-F | 功能描述:外围驱动器与原件 - PCI Quad E1 LIU RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT5894 | 制造商:EXAR 制造商全称:EXAR 功能描述:Four-Channel E1 Line Interface (3.3V or 5.0V) |
| XRT5894ES | 功能描述:外围驱动器与原件 - PCI 4 CH E1 AFE RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。