参数资料
| 型号： | XRT75L00IV |
| 厂商： | Exar Corporation |
| 文件页数： | 3/50页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| 标准包装： | 96 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-LQFP |
| 供应商设备封装： | 52-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
XRT75L00
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
9
OPERATING MODE SELECT
PIN #SIGNAL NAME
TYPE
DESCRIPTION
21
HOST/(HW)I
HOST/Hardware Mode Select:
Tie this pin “High” to configure the XRT75L00 in HOST mode. Tie this “Low” to
configure in Hardware mode.
When the XRT75L00 is configured in HOST mode, the states of many discrete
input pins are ignored.
NOTE: This pin is internally pulled up.
20
E3
I
E3 Mode Select Input
A "High" on this pin configures to operate in the E3 mode.
A "Low" on this pin configures to operate in either STS-1 or DS3 mode depend-
ing on the setting on pin 19.
NOTES:
1.
This pin is internally pulled down
2.
This pin is ignored and may be tied to GND if the XRT75L00 is
configured to operate in HOST mode.
19
STS-1/DS3
I
STS-1/DS3 Select Input
A “High” on this pin configures to operate in STS-1 mode.
A “Low” on this pin configures to operate in DS3 mode.
This pin is ignored if the E3 pin is set to “High”.
NOTES:
1.
This pin is internally pulled down
2.
This pin is ignored and may be tied to GND if the XRT75L00 is
configured to operate in HOST mode.
22
SR/DR
I
Single-Rail/Dual-Rail Select:
Setting this “High” configures both the Transmitter and Receiver to operate in
Single-rail mode and also enables the B3ZS/HDB3 Encoder and Decoder. In
Single-rail mode, Transmit input at TNData should be grounded.
Setting this “Low” configures both the Transmitter and Receiver to operate in
Dual-rail mode and disables the B3ZS/HDB3 Encoder and Decoder.
NOTE: This pin is internally pulled down.
CONTROL AND ALARM INTERFACE
42
MRING
I
Monitor Ring Input
The bipolar line output signal from TRING is connected to this pin via a 270
resistor to check for line driver failure.
NOTE: This pin is internally pulled down.
41
MTIP
I
Monitor Tip Input
The bipolar line output signal from TTIP is connected to this pin via a 270-ohm
resistor to check for line driver failure.
NOTE: This pin is internally pulled down.
40
DMO
O
Drive Monitor Output
If MTIP and MRING has no transition pulse for 128 ± 32 TxClk cycles, DMO
goes “High” to indictae the driver failure. DMO output stays “High” until the next
AMI signal is detected.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21W-MX-F4 | CONVERTER MOD DC/DC 5.5V 75W |
| MS27508E8B6PA | CONN RCPT 6POS BOX MNT W/PINS |
| XRT75L00DIVTR-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| VE-21X-MX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| MS3100A22-27S | CONN RCPT 9POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L00IV-F | 功能描述:外围驱动器与原件 - PCI Sngl Chip LIU DS3/E3 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L00IVTR | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00IVTR-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L02 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
| XRT75L02DES | 功能描述:时钟合成器/抖动清除器 2CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。