- 您现在的位置：买卖IC网 > PDF目录11653 > XTR114UA/2K5 (Texas Instruments)IC 4-20MA I-TRANSMITTER 14-SOIC PDF资料下载
参数资料
| 型号： | XTR114UA/2K5 |
| 厂商： | Texas Instruments |
| 文件页数： | 17/18页 |
| 文件大小： | 0K |
| 描述： | IC 4-20MA I-TRANSMITTER 14-SOIC |
| 标准包装： | 2,500 |
| 类型： | 电流发送器 |
| 输入类型： | 电压 |
| 输出类型： | 电压 |
| 接口： | 2 线 |
| 电流 - 电源： | 20mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
8
XTR112, XTR114
APPLICATION INFORMATION
Figure 1 shows the basic connection diagram for the XTR112
and XTR114. The loop power supply, VPS, provides power
for all circuitry. Output loop current is measured as a voltage
across the series load resistor, RL.
Two matched current sources drive the RTD and zero-
setting resistor, RZ. These current sources are 250A for the
XTR112 and 100
A for the XTR114. Their instrumentation
amplifier input measures the voltage difference between the
RTD and RZ. The value of RZ is chosen to be equal to the
resistance of the RTD at the low-scale (minimum) measure-
ment temperature. RZ can be adjusted to achieve 4mA output
at the minimum measurement temperature to correct for
input offset voltage and reference current mismatch of the
XTR112 and XTR114.
RCM provides an additional voltage drop to bias the inputs of
the XTR112 and XTR114 within their common-mode input
range. RCM should be bypassed with a 0.01F capacitor to
minimize common-mode noise. Resistor RG sets the gain of
the instrumentation amplifier according to the desired tem-
perature range. RLIN1 provides second-order linearization
correction to the RTD, typically achieving a 40:1 improve-
ment in linearity. An additional resistor is required for three-
wire RTD connections, see Figure 3.
The transfer function through the complete instrumentation
amplifier and voltage-to-current converter is:
IO = 4mA + VIN (40/RG)
(VIN in volts, RG in ohms)
where VIN is the differential input voltage. As evident from
the transfer function, if RG is not used the gain is zero and
the output is simply the XTR’s zero current. The value of RG
varies slightly for two-wire RTD and three-wire RTD con-
nections with linearization. RG can be calculated from the
equations given in Figure 1 (two-wire RTD connection) and
Table I (three-wire RTD connection).
The IRET pin is the return path for all current from the current
sources and VREG. The IRET pin allows any current used in
external circuitry to be sensed by the XTR112 and XTR114
and to be included in the output current without causing an
error.
The VREG pin provides an on-chip voltage source of approxi-
mately 5.1V and is suitable for powering external input
circuitry (refer to Figure 6). It is a moderately accurate
voltage reference—it is not the same reference used to set
the precision current references. VREG is capable of sourcing
approximately 2.1mA of current for the XTR112 and 2.4mA
for the XTR114. Exceeding these values may affect the 4mA
zero output. Both products can sink approximately 1mA.
FIGURE 1. Basic Two-Wire RTD Temperature Measurement Circuit with Linearization.
14
11
12
13
4
3
2
R
G
XTR112
XTR114
R
CM
7
1
0.01
F
I = 4mA + V
IN (
)
O
40
R
G
R
Z
RTD
6
(2)
NOTES: (1) R
Z = RTD resistance at minimum measured temperature.
R
G
R
G
V
IN
–
V
IN
+
V
LIN I
R1
I
R2
V
REG
V+
I
RET
I
O
E
B
(1)
R
G =
2.5 I
REF [R1(R2 + RZ) – 2(R2RZ)]
R
2 – R1
(2)
R
LIN1 =
where R
1 = RTD Resistance at (TMIN + TMAX)/2
R
2 = RTD Resistance at TMAX
R
LIN = 1k (Internal)
I
REF = 0.25 for XTR112
I
REF = 0.1 for XTR114
0.4 R
LIN(R2 – R1)
I
REF (2R1 – R2 – RZ)
(3)
V
PS
8
4-20 mA
I
O
0.01
F
I
R1
I
R2
7.5V to 36V
–
+
9
10
R
LIN1
(3)
R
L
V
O
Q
1
TYPE
2N4922
TIP29C
TIP31C
PACKAGE
TO-225
TO-220
Possible choices for Q
1 (see text).
XTR112: I
R1 = IR2 = 250A, RCM = 3.3k
XTR114: I
R1 = IR2 = 100A, RCM = 8.2k
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNT-IY-F1 | CONVERTER MOD DC/DC 6.5V 50W |
| D38999/20MH53SA | CONN RCPT 53POS WALL MNT W/SCKT |
| D38999/20MH55SN | CONN RCPT 55POS WALL MNT W/SCKT |
| D38999/26MG41SN | CONN PLUG 41POS STRAIGHT W/SCKT |
| D38999/26JG41SN | CONN PLUG 41POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XTR114UAE4 | 功能描述:电流灵敏放大器 4-20mA Crnt Trnsmtr w/Sensor Exc & Lin RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| XTR114UE4 | 功能描述:电流灵敏放大器 4-20mA Crnt Trnsmtr w/Sensor Exc & Lin RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| XTR115 | 制造商:BB 制造商全称:BB 功能描述:4-20mA CURRENT LOOP TRANSMITTERS |
| XTR115U | 功能描述:电流灵敏放大器 4-20mA Current Loop Transmitters RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| XTR115U | 制造商:Texas Instruments 功能描述:IC's |
发布紧急采购，3分钟左右您将得到回复。