- 您现在的位置：买卖IC网 > Datasheet目录891 > YM12S05 (Power-One)CONVERT DC/DC POL NON-ISOLATED Datasheet资料下载
参数资料
| 型号： | YM12S05 |
| 厂商： | Power-One |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | CONVERT DC/DC POL NON-ISOLATED |
| 标准包装： | 600 |
| 系列： | * |
YM12S05 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 5A
parameters, output ripple and noise, transient
response to load step-change, overload and short
circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will refer
to the vertical thermal derating for all the output
voltages in general.
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprising two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating temperatures in the application.
Thermographic imaging is preferable; if this
capability is not available, then thermocouples may
be used. . It is recommended the use of AWG #40
gauge thermocouples to ensure measurement
accuracy. Careful routing of the thermocouple leads
will further minimize measurement error. Refer to
Fig. C for optimum measuring thermocouple
locations.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 to x.2 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15m/s to 2.5 m/s), and
vertical and horizontal converter mounting.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum specified
temperature (120°C) as indicated by the
thermographic image, or
(ii) The maximum current rating of the converter (5A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. C
should not exceed 120 °C in order to operate inside
the derating curves.
Efficiency
Figure x.3 shows the efficiency vs. load current plot
for ambient temperature of 25 oC, airflow rate of 200
LFM (1 m/s) and input voltages of 9.6V, 12V and
14V.
Power Dissipation
Fig. x.4 shows the power dissipation vs. load current
plot for Ta = 25oC, airflow rate of 200 LFM (1 m/s)
with vertical mounting and input voltages of 9.6V,
12V and 14V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1 ? F ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test setup
shown in Fig. D.
i S
1 ? H
Vin
Vout
source
inductance
V source
C IN
47 ? F
ceramic
capacitor
Y-Series
DC/DC
Converter
1 ? F
ceramic
capacitor
C O
47 ? F
ceramic
capacitor
Vout
GND
GND
Fig. D:
Test setup for measuring input reflected ripple
Fig. C: Location of the thermocouple for thermal testing .
currents, i s and output voltage ripple.
MCD10132 Rev. 1.1, 21-Jun-10
Page 7 of 24
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| YNC12S20-0 | CONVERT DC/DC PROGRAM SMD |
| YNL05S10012-0 | CONVERT DC/DC 1.2V OUT 12W SMD |
| YNL12S10018-DG | CONVERT DC/DC 1.8V OUT 18W SMD |
| YNM05S05-G | CONVERT DC/DC 18.15W SMD |
| YNM12S05-G | CONVERT DC/DC 28W SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YM12S05-G | 功能描述:DC/DC转换器 0.7525-5.5Vout 5A 9.6-14VIn RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YM12S06 | 制造商:Power-One 功能描述: |
| YM-130 | 制造商:Takachi Electric Industrial 功能描述:YM^^P[X 130~90~30mm Jo[FA1050P?H24 t1.0@V[VFA1100P?H24 t1.0 Jo[FHLVo[A}Cg@V[VFJ[A~ubN Bulk |
| YM-150 | 制造商:Takachi Electric Industrial 功能描述:YM^^P[X 150~100~40mm Jo[FA1050P?H24 t1.0@V[VFA1100P?H24 t1.0 Jo[FHLVo[A}Cg@V[VFJ[A~ubN Bulk |
| YM16CNEUTRINO | 制造商:Renesas Electronics Corporation 功能描述:DEV EVALUATION KIT M16C - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。