- 您现在的位置：买卖IC网 > PDF目录48103 > YNC12S20-0G (POWER-ONE INC) 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | YNC12S20-0G |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-5 |
| 文件页数： | 27/28页 |
| 文件大小： | 337K |
| 代理商： | YNC12S20-0G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
ZD-02137 Rev. 2.1 21-Jun-10
Page 8 of 28
www.power-one.com
YNC12S20 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 20 A
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical and horizontal
mounting, efficiency, start-up and shutdown
parameters, output ripple and noise, transient
response to load step-change, overload, and short
circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will
refer to the vertical thermal derating for all the
output voltages in general.
The following pages contain specific plots or
waveforms
associated
with
the
converter.
Additional comments for specific data are provided
below.
Test Conditions
All thermal and efficiency data presented were
taken with the converter soldered to a test board,
specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers
were not metalized. The two inner layers,
comprising two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that
heat transfer from the converter to the PWB was
minimized. This provides a worst-case but
consistent scenario for thermal derating purposes.
All measurements requiring airflow were made in
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining
high reliability. If one anticipates operating the
converter at or close to the maximum loads
specified in the derating curves, it is prudent to
check actual operating temperatures in the
application. Thermographic imaging is preferable;
if
this
capability
is
not
available,
then
thermocouples
may
be
used.
Power-One
recommends the use of AWG #40 gauge
thermocouples to ensure measurement accuracy.
Careful routing of the thermocouple leads will
further minimize measurement error. Refer to Fig.
E for optimum measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15m/s to 2.5 m/s), and
vertical converter mounting. The airflow during the
testing is parallel to the short axis of the converter,
going from pin 1 and pin 6 to pins 2 – 5.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which either any MOSFET
temperature did not exceed a maximum specified
temperature
(120°C)
as
indicated
by
the
thermographic image, or
(ii) The maximum current rating of the converter
(20 A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on
the PCB at the thermocouple location shown in
Fig. E should not exceed 120 °C in order to
operate inside the derating curves.
Fig. E: Location of the thermocouple for thermal testing.
Efficiency
Figure x.2 shows the efficiency vs. load current
plot for ambient temperature of 25 C, airflow rate
of 200 LFM (1 m/s) and input voltages of 9.6 V,
12 V, and 14 V.
相关PDF资料 |
PDF描述 |
|---|---|
| YNC12S20-DS1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNC12S20-D | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| YNC12S20-DG | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| YNC12S20-0S1G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNC12S20-0 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YNC12S20A-0 | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC12S20A-0G | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC12S20A-D | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC12S20A-DG | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC12S20-D | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。