参数资料
| 型号： | YNM05S05 |
| 厂商： | Power-One |
| 文件页数： | 7/25页 |
| 文件大小： | 0K |
| 描述： | CONVERT DC/DC 18.15W SMD |
| 标准包装： | 600 |
| 系列： | * |
YNM05S05 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 5 A
Overtemperature Protection (OTP)
The converter will shut down under an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
such as system fan failure. After the converter has
cooled to a safe operating temperature, it will
automatically restart.
Safety Requirements
The converter meets North American and
International safety regulatory requirements per
UL60950 and EN60950. The maximum DC voltage
between any two pins is Vin under all operating
conditions. Therefore, the unit has ELV (extra low
voltage) output; it meets SELV requirements under
the condition that all input voltages are ELV.
The converter is not internally fused. To comply with
safety agencies’ requirements, a recognized fuse
with a maximum rating of 15 Amps must be used in
series with the input line.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnels using Infrared
(IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating temperatures in the application.
Thermographic imaging is preferable; if this
capability is not available, then thermocouples may
be used. The use of AWG #40 gauge thermocouples
is recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. E for
optimum measuring thermocouple location.
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical and horizontal
mounting, efficiency, startup and shutdown
parameters, output ripple and noise, transient
response to load step-change, overload, and short
circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will refer
to the vertical thermal derating for all the output
voltages in general.
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
Fig. E: Location of the thermocouple for thermal testing.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 to x.2 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15 m/s to 2.5 m/s), and
vertical and horizontal converter mounting.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum specified
temperature of 120 °C as indicated by the
thermographic image, or
(ii) The maximum current rating of the converter
(5 A).
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. E
MCD10190 Rev. 1.0, 21-Jun-10
Page 7 of 25
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| MC74LCX373DTR2 | IC LATCH TRANSP OCT LV 20-TSSOP |
| MC74LCX373DT | IC LATCH TRANSP OCT LV 20-TSSOP |
| OSTVE223151 | CONN TERM BLK HDR 22POS 3.81MM |
| MC74HCT373AFEL | IC LATCH TRANSP OCT 3ST 20SOEIAJ |
| MC74HCT373ADW | IC LATCH TRANSP OCT 3ST 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YNM05S05G | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 0.7525V TO 3.63V 5A 5SMD - Tape and Reel |
| YNM05S05-G | 功能描述:CONVERT DC/DC 18.15W SMD RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:* 标准包装:250 系列:* |
| YNM05S05-S | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 0.7525V TO 3.63V 5A 5SMD - Tape and Reel |
| YNM05S05-SG | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 0.7525V TO 3.63V 5A - Tape and Reel |
| YNM05S06 | 制造商:Power-One 功能描述:DCDC - Bulk 制造商:Power-One 功能描述:Module DC-DC 1-OUT 0.7525V to 3.63V 6A 5-Pin SMD |
发布紧急采购，3分钟左右您将得到回复。