- 您现在的位置：买卖IC网 > PDF目录19592 > YNV12T10-0G (Power-One)CONVERTER DC-DC 12V 10A SIP PDF资料下载
参数资料
| 型号： | YNV12T10-0G |
| 厂商： | Power-One |
| 文件页数： | 5/25页 |
| 文件大小： | 0K |
| 描述： | CONVERTER DC-DC 12V 10A SIP |
| 标准包装： | 192 |
| 系列： | Y |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 9.6V |
| 电压 - 输入（最大）： | 14V |
| Voltage - Output 1： | 0.75 ~ 5.5 V |
| 电流 - 输出（最大）： | 10A |
| 电源（瓦） - 制造商系列： | 55W |
| 安装类型： | 通孔 |
| 封装/外壳： | 10-SIP 模块 |
| 尺寸/尺寸： | 2.00" L x 0.28" W x 0.54" H（50.8mm x 7.1mm x 13.7mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 94% |
| 电源（瓦特）- 最大： | 55W |
| 产品目录页面： | 2739 (CN2011-ZH PDF) |
| 其它名称： | 179-2377 |
YNV12T10 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 10A
Nex -v Series
Operation
Vin
TM
Converter
SENSE
Input and Output Impedance
Vin
R*
ON/OFF
(Top View)
Vout
TRIM
The YNV12T10 converter should be connected via
a low impedance to DC power source. In many
6
GND
GND
5
Rload
applications, the inductance associated with the
distribution from the power source to the input of
the converter can affect the stability of the
converter. It is recommended to use decoupling
capacitors in order to ensure stability of the
converter and reduce input ripple voltage.
converter has internal input capacitance of 20 μ F
with very low ESR ceramic capacitors.
In a typical application, low - ESR tantalum or
POS capacitors will be sufficient to provide
adequate ripple voltage filtering and at the input of
the converter. However, very low ESR ceramic
capacitors 47 μ F-100 μ F are recommended at the
input of the converter in order to minimize the
input ripple voltage. They should be placed as
close as possible to the input pins of the converter.
YNV12T10 has been designed for stable operation
with or without external capacitance. Low ESR
ceramic capacitors placed as close as possible to
the load (Min 47 μ F) are recommended for
improved transient performance and lower output
voltage ripple.
It is important to keep low resistance and low
inductance PCB traces when connecting the load
to the output pins of the converter in order to
maintain good load regulation.
ON/OFF (Pin 10)
The ON/OFF pin is used to turn the power
converter on or off remotely via a system signal.
There are two remote control options available,
positive logic (standard option) and negative logic,
and both are referenced to GND. Typical
connections are shown in Fig. A.
The positive logic version turns the converter on
when the ON/OFF pin is at a logic high or left
open, and turns the converter off when at a logic
low or shorted to GND.
CONTROL
INPUT
R* is for negative logic option only
Fig. A: Circuit configuration for ON/OFF function.
The negative logic version turns the converter on
when the ON/OFF pin is at a logic low or left open,
and turns Converter off when the ON/OFF pin is at
a logic high or connected to Vin.
ON/OFF pin is internally pulled up to Vin for
positive logic version, and pulled down for
negative logic version. A TTL or CMOS logic gate,
open collector (open drain) transistor can be used
to drive ON/OFF pin. When using open collector
(open drain) transistor with a negative logic option,
add a pull-up resistor (R*) of 75K to Vin as shown
in Fig. A; This device must be capable of:
- sinking up to 0.2 mA at a low level voltage of
? 0.8V
- sourcing up to 0.25 mA at a high logic level of
2.3V – 5V
- sourcing up to 0.75 mA when connected to Vin.
Remote Sense (Pin 3)
The remote sense feature of the converter
compensates for voltage drops occurring only
between Vout pins of the converter and the load.
The SENSE pin (Pin 3) should be connected at
the load or at the point where regulation is
required (see Fig. B). There is no sense feature on
the output GND return pin, where the solid ground
plane should provide low voltage drop.
If remote sensing is not required, the SENSE pin
must be connected to any of the Vout pins to
ensure the converter will regulate at the specified
output voltage. If these connections are not made,
the converter will deliver an output voltage that is
slightly higher than the specified value.
MCD10202 Rev. 1.0, 24-Jun-10
Page 5 of 25
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| 9250A-103-RC | CHOKE RF MOLDED 10UH IRON |
| MIC5255-2.6BM5 TR | IC REG LDO 2.6V .15A SOT23-5 |
| VI-BTN-CX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| MAX6697UP9C+ | IC TEMP MON 7CH PREC 20TSSOP |
| ISPLSI 5384VA-125LB272 | IC PLD ISP 288I/O 7.5NS 272BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YNV12T10-D | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YNV12T10-DG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YNV12T16 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YNV12T16-0 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YNV12T16-0G | 功能描述:DC/DC转换器 0.7525-5.5Vout 16A 9.6-14VIn RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。