- 您现在的位置：买卖IC网 > PDF目录373781 > ZL10037LCF1 (ZARLINK SEMICONDUCTOR INC) Digital Satellite Tuner with RF Bypass PDF资料下载
参数资料
| 型号： | ZL10037LCF1 |
| 厂商： | ZARLINK SEMICONDUCTOR INC |
| 元件分类： | 消费家电 |
| 英文描述： | Digital Satellite Tuner with RF Bypass |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, QCC28 |
| 封装： | 5 X 5 MM, LEAD FREE, MO-220, QFN-28 |
| 文件页数： | 6/33页 |
| 文件大小： | 410K |
| 代理商： | ZL10037LCF1 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ZL10037
Data Sheet
6
Zarlink Semiconductor Inc.
The baseband filter uses an automatic tuning algorithm to calibrate the filter bandwidth to the programmed
requirement. This removes any variation due to operating conditions and process variations. The automatic tuning
algorithm uses a frequency locked loop, which locks the filter bandwidth to a reference frequency derived from the
crystal reference input frequency. Further details are provided in the programming section.
The filters are followed by a programmable gain stage. This provides twelve 1.5 dB gain steps. These can be used
for optimising performance at different symbol rates and for adjusting the output level in applications not using
ZL10313.
The differential outputs of each channel stage are designed for low impedance drive capability and low
intermodulation.
1.2.3 RF Bypass
The ZL10037 provides a single ended bypass function, which can be used for driving a second receiver module.
The electrical characteristics of the RF input are unchanged whether the RF bypass is enabled or disabled.
The RF Bypass powers up in the enabled state and can also operate with the remainder of the device in power
down modes.
1.3 Local Oscillator Generation
1.3.1 On Chip VCO
The local oscillator on the ZL10037 is fully integrated. It consists of three independently selectable oscillator stages
with sub bands. The three oscillators and sub-bands are designed to provide optimum phase noise performance
over the required tuning range of 950 to 2150 MHz, over operating conditions and process variations.
The local oscillators operate at a harmonic of the required local oscillator frequency and are divided down to the
required LO frequency. The required divider ratio is automatically selected by the local oscillator control logic.
The oscillators are fully controlled by an on-chip automatic tuning algorithm. The user simply programs the required
LO frequency. The control logic automatically selects the required VCO and sub band to give optimum
performance. VCO settling time is minimized as different tuning algorithms are used, depending on the magnitude
of the LO frequency change required. This choice of algorithm is also automatic and does not require user
intervention.
The oscillator control logic tracks any changes in operating conditions and will retune the VCO if necessary,
however hysteresis is built into this function to avoid unnecessary switching.
All oscillator components are included on the chip including the VCO varactor. An external loop filter is required as
part of the PLL frequency synthesizer.
1.3.2 PLL Frequency Synthesizer
The fully integrated PLL frequency synthesizer section controls the LO frequency. The only external requirements
are crystal reference and simple second order loop filter. The PLL can be operated up to comparison frequencies of
2 MHz enabling a wide loop bandwidth for maximizing the close in phase noise performance.
The local oscillator input signal is multiplexed from the active oscillator to an internal preamplifier, which provides
gain and reverse isolation from the divider signals. The output of the preamplifier provides the input to a 15-bit fully
programmable divider with MN+A architecture incorporating a dual modulus 16/17 prescaler.
The output of the programmable divider is fed to the phase comparator where it is compared in both phase and
frequency domain with the comparison frequency. This frequency is derived either from the on-board crystal
controlled oscillator or from an external reference source. In both cases the reference frequency is divided down to
the comparison frequency by the reference divider, which is programmable into 1 of 15 ratios.
相关PDF资料 |
PDF描述 |
|---|---|
| ZL10037LCG | Digital Satellite Tuner with RF Bypass |
| ZL10037LCG1 | Digital Satellite Tuner with RF Bypass |
| ZL10038LDG | MULTIMETER, DIGITAL; Accuracy, AC voltage range:+/-1.5% rdg + 3 digits; Accuracy, DC current range:+/-2.5% rdg + 3 digits; Accuracy, DC voltage range:+/-1.2% rdg + 3 digits; Accuracy, resistance range:+/-1.5%rdg + 3 digits; Current RoHS Compliant: NA |
| ZL10036 | Digital Satellite Tuner with RF Bypass |
| ZL10036LDF | Digital Satellite Tuner with RF Bypass |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL10037LCG | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Digital Satellite Tuner with RF Bypass |
| ZL10037LCG1 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Digital Satellite Tuner with RF Bypass |
| ZL10038LDG | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Digital Satellite Tuner with RF Bypass |
| ZL10039 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Digital Satellite Tuner with RF Bypass |
| ZL10039LCF | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Digital Satellite Tuner with RF Bypass |
发布紧急采购，3分钟左右您将得到回复。