参数资料
| 型号： | ZXCL260E5 |
| 厂商： | Diodes Inc |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.6V .15A SOT23-5 |
| 产品目录绘图： | LDO SOT-23-5 Top LDO SOT-23-5 Side 1 LDO SOT-23-5 Side 2 LDO SOT-23-5 Pin Out |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.6V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.155V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA（最小值） |
| 电流 - 限制（最小）： | 160mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | ZXCL260E5DKR |
ZXCL SERIES
Applications information
Enable control
A TTL compatible input is provided to allow the
regulator to be shut down. A low voltage on the
Enable pin puts the device into shutdown mode.
In this mode the regulator circuit is switched off
T d(NOM) = RCIn ?
?
and the quiescent current reduces to virtually
zero (typically less than 10nA) for input voltages
above the minimum operating threshold of the
device. A high voltage on the Enable pin ensures
normal operation.
The Enable pin can be connected to V IN or
driven from an independent source of up to 10V
maximum. (e.g. CMOS logic) for normal
operation. There is no clamp diode from the
Enable pin to V IN , so the V IN pin may be at any
voltage within its operating range irrespective
of the voltage on the Enable pin. However input
voltage rise time should be kept below 5ms to
ensure consistent start-up response.
Current Limit
The ZXCL devices include a current limit circuit
which restricts the maximum output current
flow to typically 230mA. Practically the range of
over-current should be considered as minimum
160mA to maximum 800mA. The device’s
robust design means that an output short circuit
to any voltage between ground and V OUT can be
tolerated for an indefinite period.
Thermal Overload
Thermal overload protection is included on
chip. When the device junction temperature
exceeds a minimum 125°C the device will shut
down. The sense circuit will re-activate the
output as the device cools. It will then cycle until
the overload is removed. The thermal overload
protection will be activated when high load
currents or high input to output voltage
differentials cause excess dissipation in the
device.
Start up delay
A small amount of hysteresis is provided on the
Enable pin to ensure clean switching. This
feature can be used to introduce a start up delay
if required. Addition of a simple RC network on
the Enable pin provides this function. The
following diagram illustrates this circuit
connection. The equation provided enables
calculation of the delay period.
R
C
Figure 1 Circuit Connection
T d
Figure 2 Start up delay (T d )
? V IN ?
? V IN ? 1.5 ?
Calculation of start up delay as above
? Zetex Semiconductors plc 2007
相关PDF资料 |
PDF描述 |
|---|---|
| SPX2941T5-L/TR | IC REG LDO ADJ 1A TO263-5 |
| RCA50DTAZ-S664 | CONN EDGECARD 100PS R/A .125 SLD |
| GMM36DRKI-S13 | CONN EDGECARD 72POS .156 EXTEND |
| GSM43DRKS | CONN EDGECARD 86POS DIP .156 SLD |
| ASC20DRYN-S93 | CONN EDGECARD 40POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZXCL260E5TA | 功能描述:低压差稳压器 - LDO 2.6V 150mA Sgl LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| ZXCL260E5TA | 制造商:Diodes Incorporated 功能描述:V REG LDO +2.6V SOT-23-5-5 260 |
| ZXCL260H5 | 制造商:ZETEX 制造商全称:ZETEX 功能描述:ULTRA SMALL MICROPOWER SC70 LOW DROPOUT REGULATORS |
| ZXCL260H5TA | 功能描述:低压差稳压器 - LDO 2.6V 150mA Sgl LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| ZXCL280 | 制造商:ZETEX 制造商全称:ZETEX 功能描述:ULTRA SMALL MICROPOWER SC70 LOW DROPOUT REGULATORS |
发布紧急采购，3分钟左右您将得到回复。