参数资料
型号: ZXLD1321DCATC
厂商: Diodes Inc
文件页数: 14/20页
文件大小: 0K
描述: IC LED DRVR WHITE BCKLGT 14-TDFN
特色产品: LED Driver Solutions
标准包装: 1
拓扑: PWM,升压(升压)
输出数: 1
内部驱动器:
类型 - 主要: 闪灯/白光
类型 - 次要: 高亮度 LED(HBLED),白色 LED
频率: 600kHz
电源电压: 2 V ~ 12 V
输出电压: 18V
安装类型: 表面贴装
封装/外壳: 14-TDFN 裸露焊盘
供应商设备封装: 14-DFN-EP(4x3)
包装: 标准包装
工作温度: -40°C ~ 125°C
产品目录页面: 1478 (CN2011-ZH PDF)
其它名称: ZXLD1321DCADKR
ZXLD1321
Typical operating conditions
Inductive converters can operate in either CONTINUOUS mode, where current always flows in
the inductor, but rises during the ON period and falls during the OFF period, or DISCONTINUOUS
mode, where the current falls to zero during the OFF period. The mode depends on several
factors, including supply voltage, output (LED) voltage and the choice of peak current and
inductor value. Calculations need to be done to determine which mode the converter will be in.
The circuit should be designed to give slightly more LED current than required under the lowest
supply voltage, so the control loop can regulate the current accurately. If the theoretical LED
current is less than that required, the control loop will not be able to reach the required value. The
calculations will give an idea of the ON and OFF times and hence the operating frequency, but
bear in mind that the control loop will reduce the peak current to achieve the exact programmed
LED current and this will raise the operating frequency. In general, values in the discontinuous
mode are simpler to calculate because the current can go from zero to the theoretical maximum
during the ON period and fall to zero during the OFF period. In continuous mode the current will
start from some value, so the ON time will be lower to reach the theoretical maximum and lower
still when the control loop reduces the peak current below the maximum.
Circuit operation
Operation of boost LED driver
The input voltage must always be lower than the LED voltage. This circuit has an ON phase,
where the coil is connected from the supply to ground and an OFF phase, where the coil current
flows through the LED via a Schottky diode. The current therefore only flows into the LED circuit
during the OFF phase, although the reservoir capacitor C3 should keep current flowing in the
LED(s) continuously.
ADJ is set between 50mV and 500mV to give between 10% and 100% power respectively. Making
R2 = zero gives a base current to the output transistor of 50mA nominal and making R2 = 1.68k ?
gives 10mA nominal. The reduced base current will lower supply current and hence improve
efficiency in lower power applications. Making R1 = 25m ? gives a peak coil current of 2 Amps.
The internal power transistor turns on until the coil current builds up to the peak value. At this
point the transistor switches off and the coil current continues to flow in the LED(s) via Schottky
diode D1.
Issue 1 - January 2008
? Zetex Semiconductors plc 2008
14
www.zetex.com
相关PDF资料
PDF描述
ZXLD1322DCCTC IC LED DRIVR WHITE BCKLGT 14-DFN
ZXLD1350ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
参数描述
ZXLD1322 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:BUCK/BOOST MODE DC-DC CONVERTER
ZXLD1322DCCTC 功能描述:直流/直流开关转换器 Buck-Boost DC-DC Con 0.7A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322DCCTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1322 Series 15 V 600 kHz 700 mA Buck/Boost Mode DC-DC Converter - DFN-14
ZXLD1322DCTC 制造商:ZETEX 制造商全称:ZETEX 功能描述:Buck/boost mode DC-DC converter for LED driving with 700mA output and current control
ZXLD1350 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch