- 您现在的位置：买卖IC网 > Datasheet目录370 > ZXLD1374EST20TC (Diodes Inc)IC LED DVR BUCK BOOST 20TSSOP Datasheet资料下载
参数资料
| 型号： | ZXLD1374EST20TC |
| 厂商： | Diodes Inc |
| 文件页数： | 2/39页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BUCK BOOST 20TSSOP |
| 标准包装： | 1 |
| 拓扑： | 低端，PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，通用 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 300kHz ~ 1MHz |
| 电源电压： | 6.3 V ~ 60 V |
| 输出电压： | 60V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-TSSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 其它名称： | ZXLD1374EST20TCDIDKR |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
A Product Line of
Diodes Incorporated
ZXLD1374
Pin Descriptions
Pin
Name
Pin
Type
(Note 4)
Function
Adjust Input (for DC Output Current Control).
Connect to REF to set 100% output current.
ADJ
1
I
Drive with dc voltage (125mV<V ADJ < 2.5V) to adjust output current from 10% to 200% of set value. The
ADJ pin has an internal clamp that limits the internal node to less than 3V. This prevents the LED and power
switch from delivering too much current should ADJ get overdriven.
REF
2
O
Internal 1.25V reference voltage output
Temperature Adjust (Input for LED Thermal Current Control).
T ADJ
3
I
Connect thermistor/resistor network to this pin to reduce output current above a preset temperature threshold.
Connect to REF to disable thermal compensation function (See section on thermal control).
SHP
4
I/O
Shaping capacitor for feedback control loop.
Connect 100pF ±20% capacitor from this pin to ground to provide loop compensation
Operation Status Output (analog output).
Pin is at 4.5V (nominal) during normal operation.
STATUS
5
O
Pin switches to a lower voltage to indicate specific operation warnings or fault conditions (See section on
STATUS output).
Status pin voltage is low during shutdown mode.
SGND
PGND
N/C
LX
6
7, 8
9, 10, 11, 12
13, 14
P
P
—
O
Signal Ground.
Connect to 0V and pins 7 and 8.
Power Ground.
Connect to 0V and pin 6 to maximize copper area.
Not Connected Internally.
To maximize PCB copper for thermal dissipation connect to pins 7 and 8.
Low-Side Power-Switch Output
Auxiliary Positive Supply to Internal Switch Gate Driver.
V AUX
15
P
Connect to V IN , or auxiliary supply from 6V to 15V supply to reduce internal power dissipation (Refer to
application section for more details).
At V IN >24V; to reduce power dissipation, V AUX can be connected to a 12V to 15V auxiliary power supply
(see Applications section).
Decouple to ground with capacitor close to device (refer to Applications section).
V IN
16
P
Input Supply to Device (6.3V to 60V).
Decouple to ground with capacitor close to device (refer to Applications section).
Current Monitor Input.
ISM
17
I
Connect current sense resistor between this pin and V IN .
The nominal voltage, V SENSE , across the resistor is 218mV fixed in Buck mode and initially 225mV in Boost
and Buck-Boost modes, varying with duty cycle.
Flag Open Drain Output.
FLAG
18
O
Pin is high impedance during normal operation.
Pin switches low to indicate a fault, or warning condition.
Digital PWM Output Current Control.
Pin driven either by open Drain or push-pull 3.3V or 5V logic levels.
PWM
19
I
Drive with frequency higher than 100Hz to gate output ‘on’ and ‘off’ during dimming control.
The device enters standby mode when PWM pin is driven with logic low level for more than 15ms nominal
(Refer to application section for more details).
Gain Setting Input.
Used to set the LED current in Boost and Buck-Boost modes.
GI
20
I
In Buck mode operation the GI pin must be connected to ADJ.
For Boost and Buck-boost modes , connect to resistive divider from ADJ to SGND. This defines the ratio of
switch current to LED current (see application section). The GI pin has an internal clamp that limits the
internal node to less than 3V. This provides some failsafe should the GI pin get overdriven.
EP
PAD
P
Exposed Pad.
Connect to 0V plane for electrical and thermal management.
Note:
4. Type refers to whether or not pin is an Input, Output, Input/Output or Power supply pin.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
2 of 39
www.diodes.com
September 2012
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| ZXLD1937ET5TA | IC LED DRIVR WHITE BCKLGT TSOT-5 |
| ZXLD381FHTA | IC LED DRIVR WHITE BCKLT SOT23-3 |
| ZXLD383ET5TA | IC LED DRIVR WHITE BCKLGT TSOT-5 |
| ZXSC300E5TA | IC LED DRVR WHITE BCKLGT SOT23-5 |
| ZXSC380FHTA | IC LED DRVR WHITE BCKLGT SOT23-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZXLD1601 | 制造商:ZETEX 制造商全称:ZETEX 功能描述:ADJUSTABLE DC - DC BOOST CONVERTER WITH INTERNAL SWITCH IN SC70 |
| ZXLD1601H6 | 制造商:Diodes Incorporated 功能描述:LCD/OLED BIAS BOOST CONVERTER SMD |
| ZXLD1601H6TA | 功能描述:开关变换器、稳压器与控制器 Boost Converter for LCD and OLED BIAS RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| ZXLD1601H6TC | 功能描述:开关变换器、稳压器与控制器 Boost Converter for LCD and OLED BIAS RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| ZXLD1615 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:ADJUSTABLE DC-DC BOOST CONVERTER WITH INTERNAL SWITCH IN |
发布紧急采购，3分钟左右您将得到回复。