- 您现在的位置：买卖IC网 > Datasheet目录370 > ZXLD383ET5TA (Diodes Inc)IC LED DRIVR WHITE BCKLGT TSOT-5 Datasheet资料下载
参数资料
| 型号： | ZXLD383ET5TA |
| 厂商： | Diodes Inc |
| 文件页数： | 4/10页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT TSOT-5 |
| 特色产品： | LED Driver Solutions |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 高亮度 LED（HBLED），白色 LED |
| 频率： | 330kHz |
| 电源电压： | 0.9 V ~ 2.2 V |
| 输出电压： | 20V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 工作温度： | -20°C ~ 85°C |
| 产品目录页面： | 1478 (CN2011-ZH PDF) |
| 其它名称： | ZXLD383ET5DKR |
A Product Line of
Diodes Incorporated
ZXLD383
Device Description
The ZXLD383 is a simple PFM, DC-DC controller combined with a high performance internal switching transistor, enabling
the production of a high efficiency boost converter for use in single cell applications. It includes a dual function Enable input
which serves both as an operation inhibit control and an ultra-low voltage drop isolation diode for battery charging purposes
in Garden Light applications. A block diagram is shown for the ZXLD383 in Figure 1.
With power applied and the enable pin held at V CC , an oscillator within the pulse control block forces the internal switching
transistor to switch on to start an energy charge cycle. The low saturation voltage switch pulls the V OUT pin close to ground
which forces the supply voltage across the external inductor L1. This causes a current to build up, storing energy in the
inductor. During this phase, switch current and supply voltage are monitored and used by the pulse control circuit to
determine the optimum drive conditions and on-time. At the end of the energy charge cycle, the internal switch is turned off
rapidly, interrupting the current flow through L1 which causes the voltage on V OUT to rise dramatically. When the voltage on
V OUT reaches the load LED’s forward (on) voltage, the inductor current is transferred from the internal switch to the LED,
starting the energy discharge cycle. With the voltage across the inductor reversed, the current flowing through it (and the
LED) now falls. When the inductor current reaches zero, the voltage on the V OUT pin falls back towards V CC . This action is
sensed by the pulse control circuit and is combined with the output of an off-period timer to initiate the next energy charge
cycle. Except for low level losses, all the energy stored in the inductor during a charge cycle is channeled to the load LED
during the following discharge cycle.
The current fed into the load LED has a sawtooth waveform, the average (DC) value of which is kept constant by the pulse
control circuit for varying supply voltage and temperature. It is possible to change the output current given by the ZXLD383
by changing the value of inductor L1. The larger the inductance of L1, the lower the output current. A table/graph showing
the relationship between inductance and output current is given later in this datasheet. Since the output current of the
ZXLD383 is a sawtooth waveform, its peak value is substantially larger than the DC/average value. The table also provides
this data.
The internal switching transistor has a minimum collector-emitter breakdown voltage of 20V and this sets the maximum
load voltage allowable. The minimum value is set by a feature of the pulse control circuit that requires the load voltage to
be at least 0.5V greater than V CC . (The device will function with load voltages smaller than this but output current regulation
will be impaired.) Higher than nominal load voltages will lower the average (DC) output current generated for a given
inductor value.
The Enable pin inhibits the operation of the output switch if held at a potential of Vcc-0.8V or lower. It also includes a diode
to ground which allows the input to be wired directly to a photocell array that will then both enable operation of the
converter when in darkness and charge the IC’s power source in daylight conditions. The diode function is performed by an
active circuit that gives an ultra low forward voltage drop (typically less than 0.1V at 20mA). This allows the use of a lower
output voltage photocell array (lower cost) without degrading performance.
ZXLD383
Document number: DS32189 Rev. 3 - 2
4 of 10
www.diodes.com
May 2010
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| ZXSC300E5TA | IC LED DRVR WHITE BCKLGT SOT23-5 |
| ZXSC380FHTA | IC LED DRVR WHITE BCKLGT SOT23-3 |
| ZXSC400E6TA | IC LED DRVR WHITE BCKLGT SOT23-6 |
| 0-1005447-1 | SENSOR PIEZO FILM VIBRA MASS |
| 0035.1272 | HOLDER LED SRL 5MM YELLOW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZXLD40 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SENS HEAD RFLECTV SPOT BEAM 40MM 制造商:Omron Electronic Components LLC 功能描述:Smart Sensor 11-Pin 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:DIFFUSE RFLCT SPOT BEAM 40mm |
| ZX-LD40 | 功能描述:光电传感器 DIFFUSE RFLCT SPOT BEAM 40mm RoHS:否 制造商:Omron Industrial 感应方式:Retroreflective 感应距离:2 m 光源:Infrared LED 放大器类型: 连接:Prewired Cable 输出配置:Light ON |
| ZXLD-40 | 制造商:Omron Corporation 功能描述:DIFFUSE RFLCT SPOT BEAM 40mm |
| ZXLD40L | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SENS HEAD RFLECTV LINE BEAM 40MM 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:DIFFUSE RFLCT LINE BEAM 40mm |
| ZX-LD40L | 功能描述:光电传感器 DIFFUSE RFLCT LINE BEAM 40mm RoHS:否 制造商:Omron Industrial 感应方式:Retroreflective 感应距离:2 m 光源:Infrared LED 放大器类型: 连接:Prewired Cable 输出配置:Light ON |
发布紧急采购，3分钟左右您将得到回复。