- 您现在的位置：买卖IC网 > PDF目录18581 > 0011010168 (Molex Inc)TOOL EXTRACTION FOR .084 CONTACT PDF资料下载
参数资料
| 型号： | 0011010168 |
| 厂商： | Molex Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | TOOL EXTRACTION FOR .084 CONTACT |
| 标准包装： | 1 |
| 工具类型： | 拔出工具 |
| 适用于相关产品： | 0.084 英寸触点 |
| 产品目录页面： | 217 (CN2011-ZH PDF) |
| 配用： | 0002082006-ND - CONN TERM MALE 14-20AWG TIN 0002082005-ND - CONN TERM MALE 14-20AWG TIN 0002081004-ND - CONN FEMALE TERM 14-20AWG TIN WM2294CT-ND - TERM MALE PWR BRS TIN 14-20AWG WM2291CT-ND - TERMINAL MLX 14-20AWG FEMALE WM2294TR-ND - TERM MALE PWR BRS TIN 14-20AWG WM2291TR-ND - TERMINAL MLX 14-20AWG FEMALE WM1271CT-ND - CONN TERM FEMALE 14-20AWG TIN WM1271TR-ND - CONN TERM FEMALE 14-20AWG TIN WM1271-ND - CONN TERM FEMALE 14-20AWG TIN 更多... |
| 其它名称： | 0011-01-0168 0011-01-0168-E 0011010168-E 11-01-0168 11-01-0168-E 11010168 11010168-E HT60901 WM9921 |
Quality Crimp Handbook
power to the press and remove guarding. Adjust track
SECTION 6
position. Manually cycle the press and check the feed
finger for feed location, go to procedure 7.
PROCEDURES
Tool Setup (Reference Procedures Flow Chart)
1. Check that tooling is clean and not worn. If
necessary, clean and replace worn tooling.
2. Disconnect power to the press and remove
guarding devices.
3. Install the appropriate tooling into the press.
4. Load terminals into the tooling so that the first
terminal is located over the anvil.
5. Manually cycle the press to help ensure a complete
cycle can be made without interference. If it
cannot, remove tooling and check press shut
height. Go to procedure 3.
6. Check that the tooling is aligned. Check the
impression on the bottom of the crimp that was
made by the anvil tooling. Check that the extrusions
and crimp form are centered. If not, align tooling
and go to procedure 5.
7. Check that the terminal feed locates the next
terminal over the center of the anvil tooling. If not,
adjust terminal feed and feed finger and go to
procedure 5.
8. Re-install all safety devices that were removed
during the set-up. (Follow all safety
requirements listed in individual press and/or
tooling manuals.)
9. Crimp sample terminals under power.
10. Evaluate cut-off tab length and conductor bell
mouth. If adjustment is necessary, disconnect
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Evaluate conductor brush. If adjustment is necessary,
disconnect power to the press and remove guarding.
Adjust wire stop for bench applications or press position
on automatic wire processing equipment. Go to
procedure 8.
Evaluate insulation position. If necessary, adjust strip
length, crimp new samples, and go to procedure 11.
Loosen insulation crimp height.
Crimp sample terminals.
Measure conductor crimp height and compare to
specification. If necessary, disconnect power and
remove guarding. Adjust conductor crimp height, install
guards, connect power, and go to procedure 14.
Perform a pull force test. Refer to troubleshooting
(Section 9) if this test fails.
Adjust insulation crimp.
Crimp sample terminals.
Evaluate insulation crimp. If necessary, disconnect
power and remove guarding. Adjust insulation crimp
height, install guards, connect power, and go to
procedure 18.
Measure crimp height and compare to specification. If
necessary, disconnect power and remove guarding.
Adjust conductor crimp height, install guards, connect
power, and go to procedure 18.
Document measurements.
Please Work Safely At All Times.
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 10 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 067000773001000 | HAND TOOL FOR 9176 SERIES |
| ABM2-48.000MHZ-D4YF-T | CRYSTAL 48.000 MHZ 18PF SMD |
| ASET-26.000MHZ-Y-T | OSC 26.000 MHZ 3.0V SMD |
| FQD8P10TF | MOSFET P-CH 100V 6.6A DPAK |
| CPPLC7L-B6-26.0000TS | OSCILLATOR 26.000MHZ SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0011010171 | 制造商:Molex 功能描述:OUTER JACKET STRIPPER - Bulk |
| 0011010172 | 制造商:Molex 功能描述:INNER TUBE CRIMP TOOL 制造商:Molex 功能描述:FTNER TUBE CRIMP TOOL - Bulk 制造商:Molex 功能描述:INNER CRIMP TOOL |
| 0011010173 | 制造商:Molex 功能描述:FTNER TUBE CRIMP JAWS - Bulk |
| 0011010180 | 制造商:Molex 功能描述:Hand Crimp Tool, Manual 制造商:Molex 功能描述:HAND TOOL FOR 41422 10-12 AWG |
| 0011-01-0180 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:Hand Crimper |
发布紧急采购，3分钟左右您将得到回复。