- 您现在的位置：买卖IC网 > PDF目录22831 > 03-AP24XS40 IMPACT PRINTER PANEL MTD PDF资料下载
参数资料
| 型号： | 03-AP24XS40 |
| 英文描述： | IMPACT PRINTER PANEL MTD |
| 中文描述： | 撞击式印表机面板线粒体 |
| 文件页数： | 3/10页 |
| 文件大小： | 546K |
| 代理商： | 03-AP24XS40 |
- 2 -
1
INTRODUCTION
These notes describe connection procedures to be adopted for the Able Systems Ap24XS and the
Ap24XS-40. These products feature:
Full support of EPSON M190 and M192 mechanisms
Single or double width print modes (Software selectable)
Full 224 IBM character set
Single and double height characters (Software selectable)
Inverted text mode
Dot-line graphics
8k data buffer allowing data to be received whilst printing
Serial data interface with selectable Baud rate
Serial data output for optional XON/XOFF/NAK information
Paper feed button
Easy access to paper
For an end user guide, please refer to our separate sheet.
2
IMPORTANT NOTES
Please read these carefully BEFORE proceeding
2.1 POWER SUPPLY WARNING
These products require a +5V DC power supply with a tolerance of +/-10%(+/-0.5V). For best
printing quality, it should regulated to better than +/-5%(0.25V). The current required varies with
the printing density and it is vitally important for correct initialisation and operation that the supply
can deliver sudden peak currents during operation and at start up of 5A. It is particularly important
that the initial rise-time of the supply is short enough to give a valid reset to the controller (eg 10ms
for 10% to 90%). The mean current will typically be 2A.
Note also that these products have split 5V supplies to the mechanism and controller and it is
strongly recommended that these be fed from separate regulators. The power to the controller
must
then be applied first, and removed last, if there is a significant difference in timing. The controller
supply current will be a maximum of 30mA, but the mechanism supply must be capable of 5A.
In considering the power supply arrangements, attention should be paid to the wiring and
connections, as significant voltage drops may otherwise occur. The printing performance and
reliability may be seriously affected by inadequate supply arrangements.
2.2 POWER SUPPLY TEASING
Momentary interruptions to, or reductions in the voltage of the power supply to the controller can
result in a fault condition from which it cannot recover until power is completely removed and
correctly restored. Under these conditions, the printer solenoids may be energised continuously
and burned out in a matter of seconds. The user must ensure that the supply will not be teased in
this way, or else protect the system from such effects.
The power supply must not be taken above 6V (5V +20%), or reversed, even under transient
conditions. Particular attention should be paid to the power arrangements in vehicle or battery-
operated applications, where load dump transients or reversal of replaceable batteries might occur.
Able Systems have many years' experience of the application of these products, and advice will be
freely given on request. These notes may seem severe, but what few problems occur are almost
invariably related to power supply faults.
相关PDF资料 |
PDF描述 |
|---|---|
| 03-AP25-24 | IMPACT PRINTER PANEL MTD |
| 0701ATEXFREQ1 | CRYSTAL OSCILLATOR, CLOCK, 0.04 MHz - 12 MHz, TTL OUTPUT |
| 0718BTEXFREQ2 | CRYSTAL OSCILLATOR, CLOCK, 12.1 MHz - 32 MHz, TTL OUTPUT |
| 0718XTEXFREQ3 | CRYSTAL OSCILLATOR, CLOCK, 32 MHz - 60 MHz, TTL OUTPUT |
| 0713CTXXFREQ3 | CRYSTAL OSCILLATOR, CLOCK, 32 MHz - 60 MHz, TTL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 03-AP25-24 | 制造商:ABLE SYSTEMS 功能描述:PRINTER IMPACT PANEL MTD 制造商:ABLE SYSTEMS 功能描述:PRINTER, IMPACT PANEL, MTD |
| 03AR2D | 制造商:DELTA ELECTRONICS 功能描述:EMI FILTER 115/250VAC 3A 制造商:Delta Electronics Inc 功能描述:Power Entry Module EMI Filtered M 3 POS 115VAC/250VAC 6A/4A Switch/Fuse ST 1 Port |
| 03ASR-30S | 制造商:JST Manufacturing 功能描述:ASR Series Twin U-Slot Insulation Displacement Connector 3 Point Grip Construction 3 positions |
| 03ATS2187 | 制造商: 功能描述: 制造商:GENISCO FILTER CORPORATIO 功能描述: 制造商:undefined 功能描述: |
| 03B125V10AS | 制造商: 功能描述: 制造商:undefined 功能描述: |
发布紧急采购，3分钟左右您将得到回复。