- 您现在的位置：买卖IC网 > PDF目录22831 > 03-AP24XS40 IMPACT PRINTER PANEL MTD PDF资料下载
参数资料
| 型号： | 03-AP24XS40 |
| 英文描述： | IMPACT PRINTER PANEL MTD |
| 中文描述： | 撞击式印表机面板线粒体 |
| 文件页数： | 6/10页 |
| 文件大小： | 546K |
| 代理商： | 03-AP24XS40 |
- 5 -
5
HOST PROGRAMMING
5.1 OVERVIEW
The Ap24XS interface has an 8k buffer to optimise throughput of printed data. This enables data to
be received into the buffer while previous lines are being printed, thus maximising print speed. The
buffer contents will be printed out automatically when a full line has been received (the line length
being dependent on the mechanism type and the current print mode). The buffer is cleared by a
CAN code or by a hardware reset. A partially full line will be printed on receipt of an appropriate
control code. Alternative printing modes including graphics, are invoked by 'Escape' sequences.
Each 'Escape' code sequence must be the first code in a line, i.e. it must immediately follow a valid
line termination sequence (CR or LF).
ASCII codes from 20 to FF are treated as printable characters. Codes from 00 to IF Hex are
reserved for control functions as follows:
LF (OA Hex)
Causes printout of buffer contents in selected print mode, with automatic
paper feed. If no printable characters have been received then just a paper
feed results.
VTAB (OB Hex)
Causes a fast feeding of 30 dot line pitches.
CR (OD Hex)
Behaves exactly like LF. The controller responds intelligently to
combinations of the LF and CR codes, providing an extra line feed only if
one or both of the codes is or are, repeated.
CAN (18 Hex)
Abort all printing immediately, clear the print buffer and revert to cold start
settings
ESC (lB Hex)
Causes the controller to expect the next code as a special parameter, with
its bits uniquely coded as follows:
When Bits 5 and 6 are zero:
Bit 0 (LSB)
0 for text mode
1 for data mode (inverted, reversed) printing
Bit 1
0 for characters
1 for graphics printing
Bit 2
0 for single width
1 for double width printing
Bit 3
0 for single height
1 for double height printing Bit 4 0 (except for self-test, see
below)*.
*The special combination 'ESC ESC' is used to initiate a self-test sequence, which results in a
printout of the character set.
The graphics bit is cleared to zero after each dot line (see section 4.2).
The print modes may be combined as required, for example double height and double width
inverted printing is perfectly permissible, but modes may not be mixed on one line.
When bits 5 and 6 are set, bits 4-0 take on different functions, by encoding in binary the number of
3 dot pitches the paper is to be fed.
Bit 5
0 for no fast feed
1 for fast feed
Bit 6
Must be set to 1
Bits 4-0
Binary count of number of steps.
For example, by sending 'ESC & H29' (binary 0010 1001) the controller will feed nine fast feed
steps each of three dot line pitches.
相关PDF资料 |
PDF描述 |
|---|---|
| 03-AP25-24 | IMPACT PRINTER PANEL MTD |
| 0701ATEXFREQ1 | CRYSTAL OSCILLATOR, CLOCK, 0.04 MHz - 12 MHz, TTL OUTPUT |
| 0718BTEXFREQ2 | CRYSTAL OSCILLATOR, CLOCK, 12.1 MHz - 32 MHz, TTL OUTPUT |
| 0718XTEXFREQ3 | CRYSTAL OSCILLATOR, CLOCK, 32 MHz - 60 MHz, TTL OUTPUT |
| 0713CTXXFREQ3 | CRYSTAL OSCILLATOR, CLOCK, 32 MHz - 60 MHz, TTL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 03-AP25-24 | 制造商:ABLE SYSTEMS 功能描述:PRINTER IMPACT PANEL MTD 制造商:ABLE SYSTEMS 功能描述:PRINTER, IMPACT PANEL, MTD |
| 03AR2D | 制造商:DELTA ELECTRONICS 功能描述:EMI FILTER 115/250VAC 3A 制造商:Delta Electronics Inc 功能描述:Power Entry Module EMI Filtered M 3 POS 115VAC/250VAC 6A/4A Switch/Fuse ST 1 Port |
| 03ASR-30S | 制造商:JST Manufacturing 功能描述:ASR Series Twin U-Slot Insulation Displacement Connector 3 Point Grip Construction 3 positions |
| 03ATS2187 | 制造商: 功能描述: 制造商:GENISCO FILTER CORPORATIO 功能描述: 制造商:undefined 功能描述: |
| 03B125V10AS | 制造商: 功能描述: 制造商:undefined 功能描述: |
发布紧急采购，3分钟左右您将得到回复。