- 您现在的位置：买卖IC网 > Datasheet目录560 > 0622016250 (Molex Inc)TOOL PRESS BLOCK REMOVAL Datasheet资料下载
参数资料
| 型号： | 0622016250 |
| 厂商： | Molex Inc |
| 文件页数： | 20/23页 |
| 文件大小： | 0K |
| 描述： | TOOL PRESS BLOCK REMOVAL |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062201-6250 62201-6250 622016250 |
VHDM ? and VHDM-HSD ? *
*VHDM and VHDM HSD are Trademark of Teradyne, Inc
4.2
Product Number
VHDM and HSD
(73892 Series)
Standard Tool Ordering Procedure
Tool Description
Latch Insertion Tools
62100-3915, 62100-3925
and 62100-3935
Illustration
Stacking Tooling
All the insertion tooling listed in Table 4-1 and 4-2 can be stacked
in any combination to be able to simultaneously press in any
arrangement of stacked connectors. Tooling holders are available
in various lengths. Figure 4-1 shows a typical setup for a 6 by 25
signal module, a 6 by10 signal module, and four (4) 6-row power
Figure 4-1
TYPICAL TOOLING COMBINATION
modules.
Ordering Tooling for Connectors
In order to insert a typical row of connectors, it is necessary to select the individual insertion tools and then pick the
appropriate tooling holder, (See also examples 1 and 2).
Basic Procedure
1
2
3
4
5
Determine the combination of signal modules and power modules to be inserted.
Select the proper insertion modules from Table 4-1and Table 4-2. Remember to include the appropriate
alignment block(s).
Table 4-1 and Table 4-2 shows the tool sizes. (Long) Write down the length of each tool selected.
NOTE: Make sure that if you require four of a particular tool, write down its length 4 times.
Total up these lengths.
Using the length just calculated, select the next largest tooling holder from Table 4-3. The tooling holder can
be shorter than the total tooling but not by more than 0.5 mm per side.
6
All of the tools selected above must be ordered separately.
62201-9502
Example 1
To be inserted: (1) 74059-2501 (6 by 25) Backplane Signal Module
and (1) 74029-XXXX Power Module.
1. Look at Table 4-1 and find the required tools. In this case it would
be a 62202-0208 and a 62202-0211.
2. From Table 4-1 get the lengths of these tools (numbers may be
rounded up); 62202-0208 =50.0mm and 62202-0211 = 5.4mm.
62202-0208
62202-0211
3. Add these two values for a total of 55.4mm.
4. From the Tooling Holder list in Table 4-3, pick the 72mm long
holder, 62201-9502.
5. Thus the order to Molex should include the following:
Figure 4-2
Example 1 TOOL ASSEMBLY
Doc. No: TM-622010999
Revision: H
Release Date: 08-10-99
Revision Date: 03-15-10
UNCONTROLLED COPY
Page 20 of 23
相关PDF资料 |
PDF描述 |
|---|---|
| 0622017400 | ARBOR PRESS - APPLI-MATE/RAST |
| 0622018000 | DIE FIXTURE AND DIE SET |
| 0622018626 | INSERTION TOOL MICRO TCA 170 |
| 0622018634 | 11 ROW VERT PWR MOD SUPPORT TOOL |
| 0622018635 | 15 ROW VERT PWR MOD SUPPORT TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622016400 | 制造商:Molex 功能描述:OMNI GRID POWER MODULE PRESS IN TOOL 制造商:Molex 功能描述:OMNI GRID POWER MODULE PRESS IN TOOL - Bulk 制造商:Molex 功能描述:OMNI GRID PWR MOD PRESS IN TOOL |
| 0622016600 | 制造商:Molex 功能描述:Ribbon Cable Tool Kit, Press Not Included 制造商:Molex 功能描述:CONN ACC PRESS TOOL - Bulk 制造商:Molex 功能描述:S/L RIBBON CBL ARBOR PRESS TOOL |
| 0622016601 | 功能描述:ANVIL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622016603 | 制造商:Molex 功能描述:TERM LOCATOR PINS 制造商:Molex 功能描述:TERM LOCATOR PINS - Bulk |
| 0622016615 | 功能描述:CRIMP PUNCH RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。