- 您现在的位置：买卖IC网 > Datasheet目录567 > 0638017600 (Molex Inc)PRESS TM4000 UP TO 4AWG 240AC Datasheet资料下载
参数资料
| 型号： | 0638017600 |
| 厂商： | Molex Inc |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | PRESS TM4000 UP TO 4AWG 240AC |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 系列： | TM-4000 |
| 工具类型： | 台式压机，气动 - 无喷枪 |
| 适用于相关产品： | FineAdjust? 和 Mini-Mac? 施用器 |
| 配用： | 638027600-ND - MINI MAC APPLICATOR 14-16 AWG 638027500-ND - MINI MAC APPLICATOR 18-22 AWG 638027200-ND - MINI MAC APPLICATOR 14-18 AWG 638027100-ND - MINI MAC APPLICATOR 14-18 AWG 638027000-ND - MINI MAC APPLICATOR 14-18 AWG 638026900-ND - MINI MAC APPLICATOR 14-18 AWG 0639024800-ND - FINE ADJUST APPLICATOR 0639024700-ND - FINE ADJUST APPLICATOR 0639024600-ND - FINE ADJUST APPLICATOR 0639023900-ND - FINE ADJUST APPLICATOR 更多... |
| 相关产品： | WM5083-ND - GUARD TM-3000&4000 UNIV PRESS WM6296-ND - TOOL PRESS SHUT HEIGHT GAUGE |
| 其它名称： | 063801-7600 063801-7600-E 0638017600-E 63801-7600 63801-7600-E 63801-7600-ND 638017600 638017600-E WM6378 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
TM-3000 and TM4000 Universal Press
3.1
Applicator Installation
Always turn off and disconnect the power supply to the press. Turn off the “POWER” switch located on the control
panel.
Note: Once the press guard is open the guard interlock switch will disconnect power to the motor.
Steps
1. Swing the press guard open.
2. Verify that the applicator is correctly tooled for the
terminal being used. (Reference specification sheets
supplied with the applicator).
3. Clean the press quick change mounting plate of
scrap or chips that may interfere with the applicator
PRESS
YOKE
ENGAGE
installation. Use a soft brush not compressed air.
4. Using a 4mm hex wrench, turn the M5 socket head
screw clockwise until the locking clamp is fully
opened.
LOCATOR
CLAMPS
PRESS YOKE
LUG BOLT
5. Slide the applicator lug bolt in the press yoke. See
Figure 3-1.
6. Pull down on the applicator base plate slots with the
locator clamps on the press quick change plate.
7. To lock applicator, turn M5 socket head screw
counter clockwise until tight.
QUICK
CHANGE
PLATE
LOCKING
CLAMP
USE 4mm
HEX WRENCH
BASE
PLATE
8. Confirm that the applicator is secured properly.
9. Remove the Molex ram spacer (order number
63443-7200) prior to hand cycling the press.
Figure 3-1
RAM
SPACER
Note: A ram spacer should be used when storing or transporting your applicator. Remove ram spacer proir to hand cycling
the press and replace it before removing the applicator from the press to avoid potenial damage to the tooling.
3.2
Air Feed Applicator Installation
Always turn off and disconnect the power supply to the press. Turn off the “POWER” switch located on the control
panel.
Note: Once the press guard is open the guard interlock switch will disconnect power to the motor.
Warning: When using air feed applicators, always use the slide valve to shut-off and vent air pressure before
servicing. The guard interlock switch DOES NOT remove air pressure. If an air feed is jammed and air pressure is
not removed before servicing, the feed could move unexpectedly and cause injury.
Steps
1. Swing the press guard open.
2. Verify that the applicator is correctly tooled for the terminal being used. (Reference specification sheets supplied with the
applicator).
3. Clean the press quick change mounting plate of scrap or chips that may interfere with the applicator installation. Use a
soft brush not compressed air.
4. Using a 4mm hex wrench, turn the M5 socket head screw clockwise until the locking clamp is fully opened.
5. Slide the applicator lug bolt in the press yoke. See Figure 3-1.
6. P ull down on the the applicator base plate slots with the locator clamps on the press quick change mounting
plate.
Doc. No: TM-638017299
Revision: E
Release Date: 06-06-05
Revision Date: 09-05-13
UNCONTROLLED COPY
Page 16 of 36
相关PDF资料 |
PDF描述 |
|---|---|
| 0638018000 | MINI MAC APPLICATOR - REAR FEED |
| 0638019000 | MINI MAC APPLICATOR - REAR FEED |
| 0638019250 | WIRE STRIPPER METRIC 0.3-6MM2AWG |
| 0638019700 | HAND HELD SEMI AUTO CRIMP PULLER |
| 0638021000 | MINI MAC APPLICATOR - REAR FEED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638017631 | 功能描述:CONTROL PANEL 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1 |
| 0638017701 | 制造商:Molex 功能描述:CUTTER STRIKER 制造商:Molex 功能描述:CUTTER STRIKER - Bulk |
| 0638017720 | 制造商:Molex 功能描述:TOP CUTTER 制造商:Molex 功能描述:TOP CUTTER - Bulk |
| 0638017721 | 制造商:Molex 功能描述:TOP CUTTER 制造商:Molex 功能描述:TOP CUTTER - Bulk |
| 0638017722 | 制造商:Molex 功能描述:TOP CUTTER 制造商:Molex 功能描述:TOP CUTTER - Bulk |
发布紧急采购，3分钟左右您将得到回复。