- 您现在的位置：买卖IC网 > PDF目录18581 > 0638132700 (Molex Inc)TOOL HAND EXTRACTION PDF资料下载
参数资料
| 型号： | 0638132700 |
| 厂商： | Molex Inc |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND EXTRACTION |
| 标准包装： | 1 |
| 系列： | Sabre™ |
| 工具类型： | 拔出工具 |
| 适用于相关产品： | 线至线和线至板端子 |
| 产品目录页面： | 216 (CN2011-ZH PDF) |
| 配用： | 0476341002-ND - CONN TERM ATA PWR CBL RCPT GOLD 0357480410-ND - 1.8MM WTW CRP FEMALE TERM 0357480310-ND - 1.8MM TAB AND RCPT TERM 0357470410-ND - 1.8MM WTW CRP MALE TERM 0357460410-ND - 1.8MM WTW CRP FEMALE TERM 0357450410-ND - 1.8MM WTW CRP MALE TERM 0357255210-ND - CONN RCPT TERM 14-12AWG PRE-TIN 0357255110-ND - CONN RCPT TERM 18-14AWG PRE-TIN 0040021602-ND - 250 SPADE PUSH ON CRP TERM LIF 0040021601-ND - 250 SPADE PUSH ON CRP TERM LIF 更多... |
| 其它名称： | 063813-2700 063813-2700-E 0638132700-E 63813-2700 63813-2700-E 638132700 638132700-E WM9899 |
Quality Crimp Handbook
Two operators may measure the same part differently,
or the same operator may measure the part differently
when using two types of gauges. Molex recommends a
gauge capability study to identify what part of the
variability is coming from measurement error. Micro-
terminals crimped to small wire sizes need a tight crimp
height range to maintain pull force. The variability from
measurement error can keep C pk values low.
The capability of the crimping tools needs to be re-
confirmed if the production data is significantly different
changes, or setup adjustments. Record the data point
on the chart before making a crimp height adjustment.
If data is recorded after each adjustment, the process is
likely to assume control and provide little data for
improving the process. The operator needs to make as
many notes as possible on the chart. The only truly
effective and economically sensible way to manage a
manufacturing process is to understand, monitor and
reduce sources of variability that are inherent to the
process itself. Every minute required for setup or
adjustments is unproductive.
from the capability study.
What does this sample chart tell us?
Production
Before the tool is ready for production, the level of
capability needs to be established. Many harness
manufacturers run only a few hundred or few thousand
wires at one time. In this case, it is not practical or
economical to run a twenty-five-piece capability with
every set-up.
Visual Inspection
X and R Chart
It needs to be standard operating procedure for the
operator to manually fan each bundle of crimped wires
and visually check bell mouth, conductor brush,
insulation position, cut-off tab length, and insulation
crimp.
Control Charting
Crimp height is typically control charted because it is a
quick nondestructive measurement and is critical for the
termination's electrical and mechanical reliability.
There are three primary purposes for control charting.
One, the number of setup samples is usually small, with
limited statistical value. Two, since special cause
effects on a process are irregular and unpredictable; it
is necessary to be able to catch changes in the process
as soon as they occur. This prevents thousands of
terminations from being scrapped after the run is over.
Three, and most important, this data is necessary to
assess and improve the crimp process.
Control limit for sample of 5 = Avg
(Avg of 5 readings) + .577 x Avg (Ranges)
It indicates that a process shift occurred between
measurement 12 and 13. This type of shift could occur
due to a change in wire, a change in terminal lots, a
jam in the machine that damaged the tooling, a change
in operators, or an adjustment to the insulation crimp.
Since the measurements are still within specification,
would you stop production to adjust crimp height?
A shift in the process due to a change in material may
warrant a crimp height adjustment. A shift after a jam
would not indicate an adjustment, but a close
evaluation of the tooling. A shift in the process
between operators would not indicate an adjustment,
but an evaluation of measurement capability. The
purpose of a control chart is to identify what caused the
shift in process to determine if an adjustment to the
process is needed.
Once the tooling process is setup and the wire size
does not change, keep one control chart for wire color
changes, wire length changes, terminal material
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 16 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ABM2-15.000MHZ-D4Y-T | CRYSTAL 15.000 MHZ 18PF SMD |
| SI7388DP-T1-E3 | MOSFET N-CH 30V PPAK 8SOIC |
| ABM2-32.000MHZ-D4YF-T | CRYSTAL 32.000 MHZ 18PF SMD |
| ASVMPC-14.31818MHZ-Z-T | OSC 14.31818 MHZ CMOS MEMS SMD |
| P149 | TOOL HAND INSERTION FOR T42-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638132800 | 功能描述:EXTRACTION TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0638132900 | 制造商:Molex 功能描述:EXTRACTION TOOL 制造商:Molex 功能描述:EXTRACTION TOOL - Bulk |
| 0638133100 | 功能描述:EXTRACTION TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0638133200 | 功能描述:EXTRACTOR TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0638133300 | 功能描述:EXTRACTOR TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。