- 您现在的位置：买卖IC网 > Datasheet目录570 > 0638160600 (Molex Inc)ADAPTER CRIMP FOR BAT-PWR TOOL Datasheet资料下载
参数资料
| 型号： | 0638160600 |
| 厂商： | Molex Inc |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | ADAPTER CRIMP FOR BAT-PWR TOOL |
| 标准包装： | 1 |
| 附件类型： | 压接适配器 |
| 适用于相关产品： | 0638160200 和 0638160250 |
| 配用： | WM4481-ND - TOOL CRIMP BATTERY POWERED 220V WM4480-ND - TOOL CRIMP BATTERY POWERED 110V |
| 其它名称： | 063816-0600 63816-0600 638160600 WM4483 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Battery Powered Crimping Tool
E2
POWER CRIMP
HEAD
I2
MATCH UP
MARKINGS
E1
M3 BHCS
X 8 LONG
Figure 2-11
Figure 2-10
I1
M3 BHCS X 14 LONG
FRONT
WIRE GAUGE
IDENTIFICATIONS
SHOWING
BACK
To install the locator in the Power Crimp Head
1. Install the locator assembly.
2. Press the red insert down as far as it will go. See Figure 2-12.
3. The locator goes on the opposite side from the dies with the wire gauge markings.
4. While holding onto the lower part of the locator with your thumb and index finger, insert the locator top hooks (2) into the
Power Crimp Head top slots.
5. Rotate the locator down and press the lower tabs into the two bottom slots of the head. To secure the locator into place, the
lower tabs must snap into place on the head frame.
MAKE SURE
CENTER OF LOCATOR
IS IN THE
DOWN POSITION
TOP SLOT
TOP SLOT OF
THE HANDTOOL
LOCATOR
SQUEEZE
HERE
SQUEEZE
HERE
Figure 2-13
OF THE
HANDTOOL
TOP HOOKS
Figure 2-12
Note : Make sure the longer screw only goes into the lower dies.
6. Completely close the crimp dies until they are touching, and then securely
tighten the M3 BHCS.
Power Crimp Head Installation onto Battery Powered Crimping Tool
To install the 63813-0800 Power Crimp Head onto the 63816-0200 Battery
Powered Tool, refer to Section 3 , “Set-Up and Adjustments” .
Adjustments
The crimp height on the 63816-0800 Power Crimp Head can be adjusted, if
necessary. To do this, first measure the conductor crimp height of a crimped
terminal and compare to the crimp specification listed in the product specification
for that terminal. If an adjustment is required, follow the procedure, below:
KNURLED
KNOB
LOWER TABS
LOCKING
SET SCREW
Figure 2-14
1. Loosen the locking set screw located just below the knurled knob at the top of the Power Crimp Head. See Figure 2-14.
2. If the crimp height is too loose, rotate the knob, a small amount, in the counter-clockwise direction. Crimp another
terminal and re-check the crimp height.
Order No: TM-638160200
Revision: F
Release Date: 12.06-07
Revision Date: 04-18-14
UNCONTROLLED COPY
Page 16 of 36
相关PDF资料 |
PDF描述 |
|---|---|
| 0638160900 | AT CRIMP HEAD ADAPTER |
| 0638170070 | TOOL BLADE REPLACEMENT STRAIGHT |
| 0638170100 | CUTTER CABLE STRAIGHT 20 AWG |
| 0638170200 | CUTTER CABLE CIRCULAR CROSSING |
| 0638170300 | TOOL CABLE HAND STRIP DIA 40MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638160700 | 功能描述:AIR POWERED CRIMP ADAPTER RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:- 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638160800 | 制造商:Molex 功能描述:TYPE 4D POWER CRIMP HEAD - Bulk |
| 0638160900 | 功能描述:AT CRIMP HEAD ADAPTER RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638161000 | 制造商:Molex 功能描述:BATTERY CRIMPING TOOL - Bulk |
| 0638161002 | 制造商:Molex 功能描述:BATTERY UNIT - Bulk |
发布紧急采购，3分钟左右您将得到回复。