- 您现在的位置：买卖IC网 > Datasheet目录578 > 0638851061 (Molex Inc)WIRE GUIDE FUNNEL Datasheet资料下载
参数资料
| 型号： | 0638851061 |
| 厂商： | Molex Inc |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | WIRE GUIDE FUNNEL |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 063885-1061 63885-1061 638851061 |
Wire Guide Funnel – Mylar Tape Carrier
PILOT HOLE
FLATS FACING
THE OUTSIDE
FUNNELS
ASSEMBLED
FUNNELS SHOWN
CLOSED
SETSCREW
FUNNEL SLIDE
PIVOT PINS
FIGURE 2
INSTALLATION ON APPLICATOR (See Figure 3 and 4)
1. To install the wire guide funnel, make sure the power is disconnected from the press.
2. The press ram should be fully up.
3. Replace the M8 button head cap screw that holds the
punches in the ram with the M8 by 30mm long socket
head cap screw furnished with the slide assembly. The
head of the cap screw will be used to drive the wire guide
funnel slide.
4. If the applicator uses only conductor crimp tooling it will be
necessary to stack the 7.7mm long spacer on top of the
washer.
5. If the applicator uses conductor and insulation crimp
tooling the 7.7mm long spacer is not required. See Figure
3.
6. The wire guide funnel is mounted to the two M4 threaded
holes on the lower front face of the applicator frame. The
roll pins at the top of the funnel slide block are intended to
rest on the top of the applicator frame, providing
additional stability for the slide.
7. Put (two) M4 by 35mm long socket head cap screws
through the lower holes in the slide block, then place the
Figure 3
INSULATION AND
CONDUCTOR TOOLING
7.7mm COLLAR
CONDUCTOR
TOOLING ONLY
guide spacer block over each screw.
Note: A thin film of grease applied to the guide spacer block will keep it from falling off the screw as the wire guide funnel is
mounted to the applicator.
8. Align the counterbored hole in the slide with the head of the M8 cap screw and place the wire guide funnel against the applicator
frame.
9. Using a 3mm hex wrench, tighten the two M4 screws to secure the wire guide funnel to the applicator. (Note: a small gap will exist
between the funnel guide and the applicator frame.)
10. With power disconnected, hand cycle the press to verify that the applicator ram and funnel plate slide move freely without binding.
11. Restore power to the press.
Doc No. 63885-1061
Revision: A
Release Date: 03-02-06
Revision Date: 03-02-06
UNCONTROLLED COPY
Page 2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 0638851070 | TOOL KIT |
| 0638851370 | TOOL KIT |
| 0638851470 | TOOL KIT |
| 0638851570 | TOOL KIT |
| 0638851700 | MINI MAC APPLICATOR MYLAR TAPE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638851070 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638851080 | 功能描述:FUNNEL TOOLING RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638851081 | 功能描述:FUNNEL TOOLING 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1 |
| 0638851300 | 功能描述:MINI MAC APPLICATOR MYLAR TAPE RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:Mini-Mac™, Avikrimp®, Insulkrimp®, Krimptite™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0638851370 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。