- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-1579007-6 (TE Connectivity)TOOL EXTRACTION HAND JPT Datasheet资料下载
参数资料
| 型号： | 1-1579007-6 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/2页 |
| 文件大小： | 0K |
| 描述： | TOOL EXTRACTION HAND JPT |
| 标准包装： | 1 |
| 工具类型： | 拔出工具 |
| 适用于相关产品： | 小型功率定时器触点 |
Extraction Tool 1- 1579007- 6
Instruction Sheet
408-- 8943
16 Mar 11 Rev A
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications.
Tool Tip
Tool Cover
Locking Latch
1. Depress the locking latches (Figure 1) on the
extraction tool cover and slide the cover to expose
the extraction tool tips.
2. While holding the connector, grasp the wire at
the rear of the housing and push forward toward
the mating end to disengage the contact locking
lances from the connector cavity shoulder. See
Figure 2.
Tool Handle
Locking Latch
Figure 1
1. INTRODUCTION
This instruction sheet covers the use of Extraction
Tool 1--1579007--6, which is designed to remove
Junior Power Timer (JPT) receptacle contacts and
2.8mm tab contacts from Junior Power Timer (JTP)
and 2.8mm housings.
i
NOTE Dimensions on this sheet are in millimeters
unless otherwise specified. Figures are not drawn
to scale.
2. DESCRIPTION
Extraction Tool 1--1579007--6 consists of a tool
handle, tool cover with locking latches, and an
extraction tool tip. Refer to Figure 1.
The extraction tool tips are designed to enter the
contact cavity in front of the connector and release
the receptacle contact. When the extraction tool tips
are bottomed in the contact cavity, the tips depress
the locking lances of the receptacle contact. The
contact can be removed from the housing by
manually pulling on the wire.
3. EXTRACTION PROCEDURE
Figure 2
3. Fully insert the extraction tool tips into the
windows of the circuit cavity until it bottoms inside
the window. The tips of the tool should straddle the
contact to be extracted. See Figure 3.
4. Remove the contact from the connector by
pulling on the wire attached to it.
NOTE
i
The secondary lock cover on the Junior Power
Timer (JPT) and 2.8mm tab connectors must be
in the pre--lock or open position before attempting
to remove a contact.
Figure 3
E 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111
All Rights Reserved PRODUCT INFORMATION 1--800--522--6752
TE logo is a trademark.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 2
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 1-1618058-1 | RELAY |
| 1-1618065-8 | PROTECTIVE RELAY |
| 1-1804834-1 | TOOL HAND CRIMPPER 12-26AWG |
| 1-220155-0 | TOOL DIE ASSY 10POS RIBBON COAX |
| 1-231666-1 | TOOL MODULAR PRODUCTION KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1579007-7 | 功能描述:手工工具 EXTRACTION TOOL RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1579007-8 | 功能描述:手工工具 EXTRACTION TOOL RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1579007-9 | 制造商:TE Connectivity 功能描述:Standard Insertion Tool |
| 1-1579008-0 | 制造商:TE Connectivity 功能描述:EXTRACTION TOOL TO OPEN SECONDARY LOCK |
| 1-1579008-1 | 制造商:TE Connectivity 功能描述:EXTRACTION TOOL SECONDARY LOCK OPENING - Bulk |
发布紧急采购，3分钟左右您将得到回复。