- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-1804834-1 (TE Connectivity)TOOL HAND CRIMPPER 12-26AWG Datasheet资料下载
参数资料
| 型号： | 1-1804834-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPPER 12-26AWG |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头，12-26 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | A101228-ND - SPLICE IN-LINE CRIMP YELLOW TIN A101227-ND - SPLICE IN-LINE CRIMP BLUE TIN D-436-36CS454-ND - SPLICE IN-LINE CRIMP RED TIN A101226-ND - SPLICE IN-LINE CRIMP RED TIN |
Hand Crimping Tool 1804834- 1 and
Crimping Head 1- 1804834- 1 for Raychem
MiniSeal* Splices
Instruction Sheet
408-- 10048
09 DEC 09 Rev B
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-- use, production operations is available.
!
Nest Jaw
20--26
16--20
12--16
Contact Locator
(On Back of Tool)
Anvil Jaw
release until the tool handles have been FULLY
closed.
CAUTION The crimping jaws bottom before the ratchet
releases. This feature ensures maximum
electrical and tensile performance of the crimp.
Do NOT re--adjust the ratchet.
MiniSeal Splice
CERTI-- CRIMP*
Hand Tool Ratchet
Note: Not to Scale
1. INTRODUCTION
Figure 1
Handle(s)
TE Hand
Tool/
Crimping
Head
1804834-- 1
1-- 1804834-- 1
Raychem
Splice
No. D
D-- 436-- 36
D-- 436-- 37
D-- 436-- 38
Splice
Color
Code
Red
Blue
Yellow
Crimping
Chamber
Marked
20-- 26
16-- 20
12-- 16
Wire
Size
Range
(AWG)
20-- 26
16-- 20
12-- 16
Wire
Wire
Strip
Length
7.9-- 8.6
[.31-- .34]
7.9-- 8.6
[.31-- .34]
7.9-- 8.6
[.31-- .34]
i
Double Action Hand Tool (DAHT) 1804834--1 and
Crimping Head 1--1804834--1 (shown in Figure 1) are
used to crimp Raychem MiniSeal Splices listed in
Figure 2 onto stranded wire sizes 26--12 AWG.
Read these instructions thoroughly before using the
tool.
NOTE Dimensions in this instruction sheet are in
millimeters [with inch equivalents in brackets].
Figures and illustrations are for reference only
and are not drawn to scale.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
The tool consists of a ratchet, two crimping jaws
(indenter and anvil) containing three crimping
chambers, and a terminal locator. The tool is marked
with the wire size range for each crimping chamber.
See Figure 1. Full crimping of the splice is assured by
the ratchet. Once engaged, the ratchet does not
D Qualified to MIL--S--81824/1
Figure 2
3. CRIMPING PROCEDURE
Strip the wire according to the dimensions listed in
Figure 2. The strip length is determined by the splice
and by the wire size. Do not nick or cut the wire
strands. Proceed as follows:
1. Close the tool handles until the ratchet releases.
Allow the tool handles to open fully.
2. Place the splice against the locator in the
appropriate crimp chamber. See Figure 3.
3. While holding the splice in place, squeeze the
tool handles together just until the jaws begin to
close on the wire barrel. Do NOT deform the wire
barrel.
4. Insert the stripped wire into the wire barrel,
making sure that the wire insulation does not enter
the wire barrel.
5. While holding the wire in place, squeeze the tool
handles together until the ratchet releases, then
allow the tool handles to open fully.
E 2009 Tyco Electronics Corporation, Harrisburg, PA TOOLING ASSISTANCE CENTER 1-- 800-- 722-- 1111
All International Rights Reserved PRODUCT INFORMATION 1-- 800-- 522-- 6752
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
1 of 5
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 1-220155-0 | TOOL DIE ASSY 10POS RIBBON COAX |
| 1-231666-1 | TOOL MODULAR PRODUCTION KIT |
| 1-265871-7 | TOOL PIN REPLACEMENT |
| 1-543013-6 | TOOL DIE SET CRIMP .280 CABLE |
| 1-576781-0 | TOOL HEAD CRIMP 16AWG STRATO |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1804872-0 | 功能描述:手工工具 SEATING TL ASSY POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-1 | 制造商:TE Connectivity 功能描述:SEATING TI ASSY, POW/SIG/POW - Bulk |
| 1-1804872-3 | 功能描述:手工工具 SEATING TL ASSY, POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-4 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
| 1-1804872-5 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。