- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-1804834-1 (TE Connectivity)TOOL HAND CRIMPPER 12-26AWG Datasheet资料下载
参数资料
| 型号： | 1-1804834-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPPER 12-26AWG |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头，12-26 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | A101228-ND - SPLICE IN-LINE CRIMP YELLOW TIN A101227-ND - SPLICE IN-LINE CRIMP BLUE TIN D-436-36CS454-ND - SPLICE IN-LINE CRIMP RED TIN A101226-ND - SPLICE IN-LINE CRIMP RED TIN |
Hand Crimping Tool 1804834- 1 and Crimping Head 1- 1804834- 1
408- 10048
3
1
MiniSeal Splice
ACCEPT REJECT
4
1
3
3
5
4
2
Wire Range
Stamped Here
2
1
2
3
4
5
Crimps centered. Crimps may be off center BUT NOT
OFF END OF WIRE BARREL.
Wire size matches wire color range on splice and
tool.
Wire insulation does not enter wire barrel.
Wire is visible through inspection hole of butt splices.
Wire is flush with or extends slightly beyond end of wire
barrel.
On parallel splices, bare wire ends must be flush
with or extended slightly beyond end of wire barrel.
1
2
3
4
5
6
Crimped off end of splice or terminal wire barrel.
Wire size does not match wire size or color range on
splice or tool.
Wire insulation entered wire barrel of terminal or
splice. CHECK FOR INCORRECT STRIP LENGTH.
Wire not inserted far enough in terminal or splice. End
of wire must be visible through inspection hole of butt
splices, and be flush with or extend slightly beyond end
of wire barrel.
Excessive “flash” on terminal or splice indicates damaged
jaws or wrong wire, splice, or tooling combination was
used.
Nicked or missing strands.
Figure 4
2. Close tool handles until ratchet releases and
then allow them to open freely. If they do not open
quickly and fully, the spring is defective and must
be replaced. See Section 6, REPLACEMENT AND
REPAIR.
3. Inspect head assembly for worn, cracked, or
broken jaws. Refer to Figure 5. If damage is
evident, return the tool to Tyco Electronics for
evaluation and repair. See Section 6,
REPLACEMENT AND REPAIR.
Chipped
Edge
Pitted
5.4. Gaging the Crimping Chambers
This inspection requires the use of a plug gage
conforming to the dimensions provided in Figure 6.
Tyco Electronics does not manufacture or market
these gages. To gage the crimping chambers,
proceed as follows:
1. Remove traces of oil or dirt from the crimping
chambers and plug gage.
Flattened Area
Broken Corner
Figure 5
2. Close the tool handles until it is evident that the
jaws have bottomed; then hold in this position. Do
NOT force the jaws beyond initial contact.
3. Align the GO element with the crimping
chamber. Push element straight into the crimping
chamber without using force. The GO element
must pass completely through the crimping
chamber.
Rev B
Tyco Electronics Corporation
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 1-220155-0 | TOOL DIE ASSY 10POS RIBBON COAX |
| 1-231666-1 | TOOL MODULAR PRODUCTION KIT |
| 1-265871-7 | TOOL PIN REPLACEMENT |
| 1-543013-6 | TOOL DIE SET CRIMP .280 CABLE |
| 1-576781-0 | TOOL HEAD CRIMP 16AWG STRATO |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1804872-0 | 功能描述:手工工具 SEATING TL ASSY POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-1 | 制造商:TE Connectivity 功能描述:SEATING TI ASSY, POW/SIG/POW - Bulk |
| 1-1804872-3 | 功能描述:手工工具 SEATING TL ASSY, POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-4 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
| 1-1804872-5 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。