- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-1804834-1 (TE Connectivity)TOOL HAND CRIMPPER 12-26AWG Datasheet资料下载
参数资料
| 型号： | 1-1804834-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPPER 12-26AWG |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头，12-26 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | A101228-ND - SPLICE IN-LINE CRIMP YELLOW TIN A101227-ND - SPLICE IN-LINE CRIMP BLUE TIN D-436-36CS454-ND - SPLICE IN-LINE CRIMP RED TIN A101226-ND - SPLICE IN-LINE CRIMP RED TIN |
Hand Crimping Tool 1804834- 1 and Crimping Head 1- 1804834- 1
408- 10048
Step 1
Splice Placed
Against Locator in
Crimping Chamber
Upper Jaw
Wire Being
Crimped
5. MAINTENANCE AND INSPECTION
Tyco Electronics recommends that a maintenance
and inspection program be performed periodically to
ensure dependable and uniform terminations.
Frequency of inspection depends on:
Locator
1st Wire
Lower Jaw
1. The care, amount of use, and handling of the
hand tool.
2. The presence of abnormal amounts of dust and
dirt.
Step 2
1st Wire
Splice
Upper Jaw
Wire Being
Crimped
3. The degree of operator skill.
4. Your own established standards.
The tool is inspected before being shipped; however,
Tyco Electronics recommends that the tool be
inspected immediately upon arrival at your facility to
ensure that the tool has not been damaged during
shipment.
Locator
Lower Jaw
If the wire is stripped correctly (Figure 2), the
conductor will be exposed slightly more than the
thickness of the locator. This will allow the
conductor to enter the slot in the locator
Figure 3
6. To crimp the other half of a butt splice, position
the crimped wire barrel against the locator. The
crimped wire will go through the slot in the locator.
The uncrimped barrel will line up with the crimping
chamber. Repeat the crimping procedure.
5.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
with a clean brush, or a soft, lint--free cloth. Do
NOT use objects that could damage the tool.
2. Make certain that the retaining pins are in place
and that they are secured with retaining rings.
3. All pins, pivot points, and bearing surfaces
should be protected with a thin coat of any good
SAE 20 motor oil. Do NOT oil excessively.
4. When the tool is not in use, keep handles closed
to prevent objects from becoming lodged in the
crimping jaws. Store the tool in a clean, dry area.
5.2. Lubrication
NOTE
If the splice cannot be turned for crimping other
half, turn the tool around.
Lubricate all pins, pivot points, and bearing surfaces
with SAE 20 motor oil as follows:
i
4. CRIMP INSPECTION
Inspect crimped terminals and splices by checking the
features described in Figure 4. Poor crimps can be
avoided by carefully following the procedures
provided in Section 3, and by following the tool
maintenance procedures provided in Section 5.
Tools used in daily production—lubricate daily
Tools used daily (occasional)—lubricate weekly
Tools used weekly—lubricate monthly
5.3. Periodic Inspection
1. The tool should be immersed (handles partially
closed) in a reliable commercial degreasing
compound to remove accumulated dirt, grease,
and foreign matter.
2 of 5
Tyco Electronics Corporation
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 1-220155-0 | TOOL DIE ASSY 10POS RIBBON COAX |
| 1-231666-1 | TOOL MODULAR PRODUCTION KIT |
| 1-265871-7 | TOOL PIN REPLACEMENT |
| 1-543013-6 | TOOL DIE SET CRIMP .280 CABLE |
| 1-576781-0 | TOOL HEAD CRIMP 16AWG STRATO |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1804872-0 | 功能描述:手工工具 SEATING TL ASSY POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-1 | 制造商:TE Connectivity 功能描述:SEATING TI ASSY, POW/SIG/POW - Bulk |
| 1-1804872-3 | 功能描述:手工工具 SEATING TL ASSY, POW/SIG/POW RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1804872-4 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
| 1-1804872-5 | 功能描述:SEATING TL ASSY, POW/SIG/POW 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。