- 您现在的位置：买卖IC网 > PDF目录68762 > 1027LE-28TE13 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 PDF资料下载
参数资料
| 型号： | 1027LE-28TE13 |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 封装： | PLASTIC, DIP-8 |
| 文件页数： | 15/17页 |
| 文件大小： | 108K |
| 代理商： | 1027LE-28TE13 |
7
Preliminary Information
CAT1026, CAT1027
Doc No. 3010, Rev. E
Data Protection
The CAT1026 and CAT1027 devices have been designed
to solve many of the data corruption issues that have long
been associated with serial EEPROMs. Data corruption
occurs when incorrect data is stored in a memory location
which is assumed to hold correct data.
Whenever the device is in a Reset condition, the embedded
EEPROM is disabled for all operations, including write
operations. If the Reset output(s) are active, in progress
communications to the EEPROM are aborted and no new
communications are allowed. In this condition an internal
write cycle to the memory can not be started, but an in
progress internal non-volatile memory write cycle can not
be aborted. An internal write cycle initiated before the
Reset condition can be successfully finished if there is
enough time (5ms) before VCC reaches the minimum
value of 2V.
In addition, to avoid data corruption due to the loss of
power supply voltage during the memory internal write
operation, the system controller should monitor the
unregulated DC power. Using the second voltage sensor,
VSENSE, to monitor an unregulated power supply, the
CAT1026 and CAT1027 signals an impending power
failure by setting VLOW low.
Watchdog Timer
The Watchdog Timer provides an independent protection
for microcontrollers. During a system failure, the CAT1027
device will provide a reset signal after a time-out interval
of 1.6 seconds for a lack of activity. CAT1027 is designed
with the Watchdog timer feature on the WDI pin. If WDI
does not toggle within 1.6 second intervals, the reset
condition will be generated on reset output. The watchdog
timer is cleared by any transition on monitored line.
As long as reset signal is asserted, the watchdog timer
will not count and will stay cleared.
DEVICE OPERATION
Reset Controller Description
The CAT1026 and CAT1027 precision RESET
controllers ensure correct system operation during
brownout and power up/down conditions. They are
configured with open drain RESET outputs.
During power-up, the RESET outputs remain active
until VCC reaches the VTH threshold and will continue
driving the outputs for approximately 200ms (tPURST)
after reaching VTH. After the tPURST timeout interval, the
device will cease to drive the reset outputs. At this point
the reset outputs will be pulled up or down by their
respective pull up/down resistors.
During power-down, the RESET outputs will be active
when VCC falls below VTH. The RESET output will be
valid so long as VCC is >1.0V (VRVALID). The device is
designed to ignore the fast negative going VCC transient
pulses (glitches).
Reset output timing is shown in Figure 1.
Manual Reset Capability
The
RESET pin can operate as reset output and manual
reset input. The input is edge triggered; that is, the
RESET input will initiate a reset timeout after detecting
a high to low transition.
When
RESET I/O is driven to the active state, the 200
msec timer will begin to time the reset interval. If external
reset is shorter than 200 ms, Reset outputs will remain
active at least 200 ms.
Monitoring Two Voltages
The CAT1026 and CAT1027 feature a second voltage
sensor, VSENSE, which drives the open drain VLOW
output low whenever the input voltage is below 1.25V.
The auxiliary voltage monitor timing is shown in Figure
2.
By using an external resistor divider the sense circuitry
can be set to monitor a second supply in the system.
The circuit shown in Figure 3 provides an externally
adjustable threshold voltage, VTH_ADJ to monitor the
auxiliary voltage. The low leakage current at VSENSE
allows the use of large value resistors, to reduce the
system power consumption. The VLOW output can be
externally connected to the RESET output to generate
a reset condition when either of the supplies is invalid.
In other applications, VLOW signal can be used to
interrupt the system controller for an impending power
failure notification.
相关PDF资料 |
PDF描述 |
|---|---|
| 1027LI-28TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 1027ZI-45TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 1026PA-30TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 1027PE-45TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 1027SI-28TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1027R | 制造商:Thomas & Betts 功能描述:REPLACEMENT INTERIOR |
| 1028 | 功能描述:电池座、电池扣和电池接头 Battery HOLDER PC AA RoHS:否 制造商:Eagle Plastic Devices 产品:Battery Snaps 电池组电池大小:9 V 电池数量:1 端接类型:Snaps 颜色:Black 材料:Polyvinyl Chloride (PVC) 安装风格:Snap-In |
| 1028 | 制造商:Keystone Electronics Corp 功能描述:Battery Holder |
| 1028.09.540-500 | 制造商:Walter schrickel 功能描述: |
| 1028.09.541-500 | 制造商:Walter schrickel 功能描述:Bulk |
发布紧急采购，3分钟左右您将得到回复。