- 您现在的位置：买卖IC网 > PDF目录68762 > 1027LE-28TE13 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 PDF资料下载
参数资料
| 型号： | 1027LE-28TE13 |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 封装： | PLASTIC, DIP-8 |
| 文件页数： | 17/17页 |
| 文件大小： | 108K |
| 代理商： | 1027LE-28TE13 |
9
Preliminary Information
CAT1026, CAT1027
Doc No. 3010, Rev. E
EMBEDDED EEPROM OPERATION
The CAT1026 and CAT1027 feature a 2kbit embedded
serial EEPROM that supports the I2C Bus data
transmission protocol. This Inter-Integrated Circuit Bus
protocol defines any device that sends data to the bus to
be a transmitter and any device receiving data to be a
receiver. The transfer is controlled by the Master device
which generates the serial clock and all START and
STOP conditions for bus access. Both the Master device
and Slave device can operate as either transmitter or
receiver, but the Master device controls which mode is
activated.
I2C Bus Protocol
The features of the I2C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT1026 and CAT1027
monitor the SDA and SCL lines and will not respond until
this condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant
bits of the 8-bit slave address are programmable in metal
and the default is 1010.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this bit
is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT1026 and CAT1027 monitor the
bus and responds with an acknowledge (on the SDA
line) when its address matches the transmitted slave
address. The CAT1026 and CAT1027 then perform a
Read or Write operation depending on the R/
W bit.
tHIGH
SCL
SDA IN
SDA OUT
tLOW
tF
tLOW
tR
tBUF
tSU:STO
tSU:DAT
tHD:DAT
tHD:STA
tSU:STA
tAA
tDH
Figure 4. Bus Timing
Figure 5. Write Cycle Timing
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
ACK
8TH BIT
BYTE n
SCL
SDA
相关PDF资料 |
PDF描述 |
|---|---|
| 1027LI-28TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 1027ZI-45TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 1026PA-30TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 1027PE-45TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 1027SI-28TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1027R | 制造商:Thomas & Betts 功能描述:REPLACEMENT INTERIOR |
| 1028 | 功能描述:电池座、电池扣和电池接头 Battery HOLDER PC AA RoHS:否 制造商:Eagle Plastic Devices 产品:Battery Snaps 电池组电池大小:9 V 电池数量:1 端接类型:Snaps 颜色:Black 材料:Polyvinyl Chloride (PVC) 安装风格:Snap-In |
| 1028 | 制造商:Keystone Electronics Corp 功能描述:Battery Holder |
| 1028.09.540-500 | 制造商:Walter schrickel 功能描述: |
| 1028.09.541-500 | 制造商:Walter schrickel 功能描述:Bulk |
发布紧急采购，3分钟左右您将得到回复。