- 您现在的位置：买卖IC网 > Datasheet目录590 > 11-01-0185 (Molex Connector Corporation)TOOL HAND CRIMP .100 TERM RACHET Datasheet资料下载
参数资料
| 型号： | 11-01-0185 |
| 厂商： | Molex Connector Corporation |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP .100 TERM RACHET |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 系列： | KK® |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，22-30 AWG |
| 特点： | 侧面插入，棘齿 |
| 其它名称： | 0011-01-0185 0011-01-0185-E 0011010185 0011010185-E 11-01-0185-E 11010185 11010185-E CR2262C WM9915 |
Hand Crimp Tool for .100 KK
How To Adjust Tool Crimp Force (See Figure 4)
It may be necessary over the life of the tool to adjust tool-crimping force. Listed below are the steps required to
adjust the crimping force of the hand tool to obtain proper crimp conditions:
1. Remove the screw and washer. Located over the adjustment ring.
2. Lift the adjusting ring slightly, off of the locating pin.
3. Turn the adjusting ring in the desired direction (L= less force, T= more force) to increase or decrease crimp
pressure.
4. Press the adjusting wheel flat against the tool and engage the locking pin.
5. Replace the washer and screw.
6. Check the crimp specifications after tool crimp force is adjusted.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we would exchange the tool free of charge. This will not be applicable to
altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of
handle extensions voids this warranty.
Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.
Caution: Repetitive use of this tool should be
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above).
Variations in tools, terminals, wire stranding and insulation types may affect crimp height.
3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all
insulation sizes.
4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts
available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no
influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips
on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping
Handbook 63800-0029 for additional information on crimping and crimp testing.
6. Molex does not certify crimp hand tools.
CAUTION : Molex crimp specifications are valid only when used with Molex terminals, applicators and
Doc No. 11-01-0185
Revision: E
Release Date: 10-07-03
Revision Date: 08-11-04
UNCONTROLLED COPY
Page 5 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 1102855-3 | TOOL EXTRACTION SOLARLOK |
| 1116571-1 | CUTTER SIDE TAPERED FLUSH 4.88" |
| 1120380003 | DIGITAL MOD 4PORT 8OUTPUTS PNP |
| 1120380005 | DIGITAL MOD 4PORT 4IN 4OUT NPN |
| 1120380006 | DIGITAL MOD 4PORT 4IN 4OUT PNP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 11-01-0185 REPAIR | 制造商:MOLEX 功能描述: |
| 11-01-0185 | 制造商:Molex 功能描述:TOOLSCRIMPHANDHAND CRIMPER 22/24/26/ |
| 11-01-0189 | 功能描述:折皱器 CRIMP HANDTOOL 22-28 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 11-01-0193 | 功能描述:折皱器 SPOX CRIMPER 18-24 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 11-01-0194 | 功能描述:折皱器 HAND CRIMP TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。