参数资料
| 型号： | 118213-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | HSG-RECP ECONOMATE 2 |
| 标准包装： | 1,000 |
| 系列： | Economate II |
| 连接器类型： | 插座 |
| 请注意： | 不提供触点 |
108-12057
Test Description
Durability.
Engaging force.
Separating force.
Contact retention.
Torque.
Pin shield retention.
Requirem ent
See Note.
10 ounces m axim um average per
contact.
1 ounce m inim um average per
contact.
Contacts shall not dislodge when a
m inim um axial force of 15 pounds
for soldered contacts and 7 pounds
for press-fit contacts is applied in
either direction.
Contacts shall not dislodge when a
m axim um force of 3 inch-ounces is
applied in both directions.
Pin shield shall not separate from
the housing nor exhibit dam age or
defects that would im pair norm al
function when a m axim um force of
4 pounds is applied to each end of
each pin shield.
Procedure
Mate and unm ate specim ens with a
corresponding blade header
assem bly for 100 cycles at a
m axim um rate of 10 cycles per
m inute.
Measure force required to m ate
specim ens with a corresponding
blade header assem bly.
Measure force required to withdraw
a m inim um size gage from each
individual contact.
See Figure 4.
Apply specified axial load to contact
posts in a direction toward the
connector and hold for 5 to 10
seconds.
Apply specified force to the base of
each contact post in both clockwise
and counterclockwise directions
and hold for 5 to 15 seconds.
MIL-C-28754, paragraph 4.9.6.
Apply specified force in a direction
norm al to a plane passing through
the center line of both keying pins
m idway between the first and
second cavities and .062 +.000/-
.031 inch from the bottom edge of
the shield.
See Figure 5.
ENVIRONMENTAL
Therm al shock.
Salt spray.
See Note.
See Note.
MIL-STD-202, Method 107, Test
Condition A.
Subject specim ens to 5 cycles
between -55 and 105 / C.
MIL-STD-202, Method 101, Test
Condition B.
Subject specim ens to 5% salt spray
solution for 48 hours. After
exposure, specim ens shall be
thoroughly washed using tap water
and dried at 100 / F for 24 hours
before proceeding with additional
testing.
Figure 1 (continued)
Rev E
3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 118438-1 | CONN RCPT 53POS .100 GOLD |
| 119272-8 | CONN RCPT CONTACT .100 GOLD |
| 1217001-1 | CONN RCPT/TAB FAST 20-16AWG .187 |
| 1217002-1 | CONN UNINSUL TAB 0.250 |
| 1217003-1 | CONN UNINS RECPT 14-18AWG 0.110 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 11821-CK | 制造商:Thomas & Betts 功能描述:11821 DIE FOR #10 INSULATED CK LUGS |
| 1182-1INX18YDS | 制造商:3M Electronic Products Division 功能描述:80610875926 |
| 11821U | 制造商:RAY ENGINEERING 功能描述:INDEX PLUNGER,REST,6MM |
| 11822 | 制造商:Thomas & Betts 功能描述:WT-117 DIE SET 制造商:Thomas & Betts 功能描述:Plier Type Tools |
| 11-822 | 功能描述:SKT PHLP BIT 3/8DR #2 制造商:apex tool group 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。