- 您现在的位置：买卖IC网 > PDF目录293732 > 1245FAFC (TRIQUINT SEMICONDUCTOR INC) TRANSMITTER PDF资料下载
参数资料
| 型号： | 1245FAFC |
| 厂商： | TRIQUINT SEMICONDUCTOR INC |
| 元件分类： | 数字传输电路 |
| 英文描述： | TRANSMITTER |
| 封装： | PLASTIC, DIP-20 |
| 文件页数： | 7/12页 |
| 文件大小： | 201K |
| 代理商： | 1245FAFC |
4
Lucent Technologies Inc.
Data Sheet
1241/1243/1245-Type Uncooled Laser Transmitter
September 1999
Functional Overview (continued)
Since most applications operate at very high data
rates, high-frequency design techniques need to be
used to ensure optimum performance from the trans-
mitter and interfacing circuitry. Input signal paths
should be kept as short and as straight as possible; dif-
ferential signal lines should be equal in length, and
controlled-impedance stripline or microstrip construc-
tion should always be used when laying out the printed-
wiring board traces for the data lines. The Recom-
mended User Interfaces section of this data sheet
shows several methods of interfacing to the transmitter.
Power Supplies
The transmitter is congured for operation from either a
single +5 V power supply or a single –5 V power supply.
For positive power supply operation, connect Vcc to the
+5 V power supply and connect VEE to ground or circuit
common. For operation from a –5 V power supply, con-
nect VCC to ground and connect VEE to the –5 V power
supply. Whichever option is chosen, the VCC or VEE con-
nection to the transmitter should be well ltered to pre-
vent power supply noise from interfering with
transmitter operation.
Transmitter Specications
Optical Output Power
During manufacture, the optical output power of every
transmitter is tuned to the typical value specied in the
data sheet for that particular transmitter code. The tun-
ing is performed at room ambient and a power supply
voltage of 5 V. The minimum and maximum values
listed in the data sheet for each code group reect the
worst-case limits that the transmitter is expected to
operate within over its lifetime and over the allowed
power supply and the operating temperature range.
Every transmitter shipped receives a nal test, which
includes a SONET eye-mask test at either the OC-3
(STM-1) data rate of 155.52 Mbits/s, the OC-12
(STM4) data rate of 622.08 Mbits/s, or the bre channel
FC-0 data rate of 1062.5 Mbits/s. The eye-mask test is
meant to examine the performance of the transmitter's
output optical waveform relative to a minimum data pat-
tern eye opening.
Connector Options
The standard optical ber pigtail is 8
m core single-
mode ber having a 0.036 in. (914
m) diameter tight-
buffered outer-jacket. The standard length is 39 in.
±
4 in. (1 m
± 10 cm) and can be terminated with either
an SC or FC-PC optical connector. Other connector
options may be available on special order. Contact your
Lucent Account Manager for ordering information.
Handling Precautions
CAUTION: This device is susceptible to damage as
a result of electrostatic discharge (ESD).
Take proper precautions during both
handling and testing. Follow guidelines
such as JEDEC Publication No. 108-A
(Dec. 1988).
Although protection circuitry is designed into the
device, take proper precautions to avoid exposure to
ESD. Lucent employs a human-body model (HBM) for
ESD-susceptibility testing and protection-design evalu-
ation. ESD voltage thresholds are dependent on the
critical parameters used to dene the model. A stan-
dard HBM (resistance = 1.5 k
, capacitance = 100 pF)
is widely used and, therefore, can be used for compari-
son purposes. The HBM ESD withstand voltage estab-
lished for the 1241-/1243-Type Transmitter is
±1000 V.
Transmitter Processing
The transmitter can withstand normal wave-soldering
processes. The complete transmitter module is not her-
metically sealed; therefore, it should not be immersed
in or sprayed with any cleaning solution or solvents.
The process cap and ber pigtail jacket deformation
temperature is 85
°C. Transmitter pins can be wave-
soldered at maximum temperature of 250
°C for
10 seconds.
Installation Considerations
Although the transmitter features a robust design, care
should be used during handling. The optical connector
should be kept free from dust, and the process cap
should be kept in place as a dust cover when the
device is not connected to a cable. If contamination is
present on the optical connector, canned air with an
extension tube can be used to remove any debris.
Other cleaning procedures are identied in the techni-
cal note,
Cleaning Fiber-Optic Assemblies (TN95-
010LWP).
相关PDF资料 |
PDF描述 |
|---|---|
| 1245CBDC | TRANSMITTER |
| 1245CAFC | TRANSMITTER |
| 1243FBDC | TRANSMITTER |
| 1243FAFD | TRANSMITTER |
| 1243CBDC | TRANSMITTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1245FBDC | 制造商:AGERE 制造商全称:AGERE 功能描述:1241/1243/1245-Type Uncooled Laser Transmitter |
| 1245G0 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC |
| 1245G1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC |
| 1245G2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC |
| 1245M0 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC |
发布紧急采购，3分钟左右您将得到回复。