- 您现在的位置：买卖IC网 > PDF目录11500 > 127-0711-601 (Emerson Network Power Connectivity Johnson)CONN SMP MALE HERMETIC SEAL PDF资料下载
参数资料
| 型号： | 127-0711-601 |
| 厂商： | Emerson Network Power Connectivity Johnson |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | CONN SMP MALE HERMETIC SEAL |
| 产品目录绘图： | 127-(0,1,2)711-601 |
| 特色产品： | SMP Blind-Mate Connectors |
| 标准包装： | 5 |
| 系列： | SMP |
| 附件类型： | 真空密封 |
| 适用于相关产品： | SMP 连接器 |
| 特点： | 全方位锁销 |
| 其它名称： | J10018 |
Connectivity for
SMP Connectors
Assembly Instructions
ASSEMBLY INSTRUCTIONS
SMP Straight Female Solder Style for .047 OD Semi-Rigid Cable
1 Identify tools (5 piece parts) and connector parts (3 piece parts).
2. Strip cable jacket and dielectric to dimension shown. Do not
nick center conductor. Clean all debris from prepared cable.
3. Insert center conductor into cable stop as shown and place
contact onto center conductor.
4. Insert contact into contact holder fixture and clamp cable in vise.
Tighten stop screw until light pressure is applied between con-
tact, cable stop and cable jacket.
5. Solder contact to center conductor through solder hole using
.016 (0.41) diameter flux core solder wire or solder paste. Use a
minimum amount of solder and heat for a good joint. Do not
allow heat to build up for a long period of time as cable stop
may melt.
6. After solder joint has cooled, remove cable from vise. Remove
any excess solder from contact with a sharp blade and clean all
debris from contact and cable.
7. Insert contact into connector assembly, making sure cable stop
bottoms out against internal shoulder of connector body. Insert
connector assembly into interface location fixture and clamp
cable in vise. Make sure connector assembly is fully engaged
within location fixture. Tighten stop screw until light pressure is
applied between connector assembly and cable stop.
8. Solder end of connector body to cable jacket, using a minimum
amount of solder and heat for a full fillet joint. Allow assembly to
cool before removing connector from vise and location fixture.
Best results are obtained when contact location is flush to .004
(0.10) recessed from reference plane. Interface location fixture
is pre-set at factory, but can be adjusted to control location.
Business-Critical Continuity
Cable Group
MIL-C-17/151, .047 Semi-Rigid
Tool
Cable Vise
Stop Screw
Clamp Inserts
Contact Holder
Interface Location Fixture
14
Part Number
127-0692-001
Part Number
140-0000-962
140-0000-981
140-0000-997
127-0000-902
127-0000-903
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16F913-E/ML | IC PIC MCU FLASH 4KX14 28QFN |
| ADG719BRTZ-REEL7 | IC SWITCH SPDT SOT23-6 |
| PIC24FV16KA301-E/SO | IC MCU 16B 16KB FLASH 20SOIC |
| ADG702BRJZ-REEL7 | IC SWITCH SPST SOT23-5 |
| VI-B3B-CU-F2 | CONVERTER MOD DC/DC 95V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 12-7071-CARD | 制造商:GC Electronics 功能描述: |
| 127072 | 制造商:Brady Corporation 功能描述:B401 10X14 BLK/ORG WARNING DO NOT ENTER |
| 12-7072 | 制造商:GC Electronics 功能描述: |
| 127073 | 制造商:Brady Corporation 功能描述:B302 10X14 BLK/ORG WARNING DO NOT ENTER |
| 12-7073 | 制造商:GC Electronics 功能描述:Micro Round Nose Pliers |
发布紧急采购，3分钟左右您将得到回复。